28 foot hunter sailboat

• David Pascoe
• All Articles (over 180)
• Mid Size Power Boats
• Buyers' Guide to Outboard Boats
• Surveying Fiberglass Power Boats (2E)
• Marine Investigations
• Domestic (USA)
• International
• Privacy Policy
• All Articles
• Order Books

• Boat Reviews
• Buying a Boat
• Cores & Structural Issues
• Marine Engines
• Maintenance & Repairs
• Hull Blisters
• Marine Surveying
• Insurance Issues
• Boat Handling & Boat Safety
• Hurricane Preparations
• Fuel Issues

Read Online

Full Chapter One

by David Pascoe

First impressions are often lasting ones, especially when they are negative impressions like my first experience with Hunter in the early 1980's. Back then I had been hired by an unfortunate Hunter owner who had a forty footer with a grid liner that all came apart, causing some serious structural problems. At the time, Hunter had just converted to the use of grid liners (one of, if not the first to do so) and were far from perfecting the method, once again proving my point that far too many boat builders perform their experimentation in their product line, at the expense of their customers.

After much haggling we finally got that straightened out, but when you see stuff like that, you don't soon forget. Your opinion of a builder is ever afterward tainted. So we weren't too surprised to see that Hunter had finally got the grid liner right in this 1991 model. While this is unquestionably a low price boat, overall it seemed to be fairly well built and there were no problems with the framing system at all.  

The interior has a complete fiberglass liner that is well executed.  With the mast stepped on deck, there was no sign of the structural weakness in the cabin to as is so often the case with this type of boat.We were also suprised to find that there were no significant leaks inside.   The deck is bolted on a horizontal flange joint with bolts every 3", but it couldn't be determined if the joint was glassed over since nowhere in the boat could the deck joint be seen. The decks and cockpit area seemed sturdy enough and there were no stress cracks anywhere on the exterior decks, except in way of the poorly designed bow pulpit leg bases where there was considerable crazing.

With the sole angled at 45 degrees and the standup space only 20" wide by 5' long, this is not exactly good design.

The interior layout, like most boats this size, attempts to cram too much into too small a space. Despite it's 10'6" beam, its pretty cramped inside, mainly owning to faux "aft cabin" that is just a cave behind the engine with a cushion on the floor. The cushions being vinyl over foam rubber, this might lead to a rather sleepless nights in warm weather. Like wrapping yourself in insulation. The aft cabin area cuts into the main cabin area, rendering it somewhat less than useful. In fact, judging from the pristine condition of the galley stove, icebox and other interior components, this boat looked like it had been used as a day sailor only. It was now going on its third owner in 9 years. After spending a few hours aboard her, we could understand why.

We can understand that because the sole in the head is above the turn of the bilge so that it is steeply angled and one can hardly even stand up in there. The ladies will love it since to sit on the head, you sort of have to fall down onto it because it is very low, not at normal height. Ouch! And the guys will love trying to stand up on the 45 degree angled sole.  The area is also a deep rectangle, making it very awkward to enter, altogether a terrible layout in my view. The entrance to the "aft cabin" is the same way with the steeply angled sole, causing your feet to slip every time you step on it. Add to this the fact that the aft-facing, U-shaped settee in the main cabin has a seat width that is too narrow to sit comfortably, and we think the overall layout is a flop. With a drop leaf table in the center, the only place anyone will sit is at the ends, rendering the main part of the settee rather unuseable. So the effective interior seating capacity is two. The only thing we found convenient to use was the galley area. The interior is under-scaled for anyone over about 5'6" and a trim build.

The hull-recessed swim platform is a nice feature on larger boats, but this boat is too small for it. Basically it just allows a swimmer to get aboard, but at the considerable expense of interior and cockpit space. Sacrificing two feet of space for a steeply reversing transom on a 28 footer is an unreasonable  price to pay for style in our view. One really nice feature was the bow anchor locker which is one of the few that we've seen that is well designed.

Yes, we recognize that you're not going to get perfection in a budget priced 28 footer, but you can do a lot better than this. Here we go again with the rigging going down through the deck right in the middle of the traffic pattern. Getting around the rigging is a real pain. That's because to keep the price down, they went with a 3/4 instead of full head rig, with extraordinarily light rigging with only single lowers. The uppers were only 0.20" and the lowers and wishbone backstay a mere 0.15" wire! Would you want  to sea in a boat rigged like that? Not me, no thank you. Time has made of me a believer in safety margins.  Every time a gust of wind would come up, I'd have to wonder if the rig was going to fall down. Yike!

This is one of the major problems of the so-called racer-cruiser. It is the ultimate compromise of everything that leaves you happy with nothing. You want to win races and cruise, but its poorly suited for either.

Nor will you likely appreciate the very small deck hatch that makes stowing a sail rather difficult but, then, this one had roller furling that, unfortunately, couldn't be tensioned adequately because of the lightness of the rig. Wishbone back stays are not exactly the best arrangement for roller furling gear. Going racing with roller furling? Don't think so.

Next, lets talk about cockpit design. It had the large 30" destroyer wheel, which is fine except you have to crawl over the seats to get to the helm. That's the price you pay for a large wheel in any small boat. But what really ruins this cockpit layout was the sheet winch islands which are shallow and steeply sloping outboard, with no horizontal surface. Okay, so it makes the winches more or less level when heeled. Problem is that when you're tacking, the boat is not heeled over so much, and the winches would be more level if they were mounted in the normal manner. But in addition to this, you no longer have any back support while sitting in the cockpit, so that you cannot sit on the leeward side at all without continuously hanging on for dear life when heeled over even just a bit. When I leaned back against it, it hit me right in the small of my back, making it very uncomfortable. My feeling was that the lack of any raised coamings to lean back against was just plain ridiculous. Sail boat cockpits tend to be uncomfortable anyway, but this is one of the worst I've seen.

Plus, this design has also created a steeply sloping deck section in way of the winch island that about wants to break your ankle when you step on it. With a Bimini top, getting in and out of the cockpit is something of a Houdini trick as it is on most boats. But constantly climbing over the lifelines because there is no life line gate there didn't improve my disposition much. The owner had to install a small aluminum step on the outside of the rail just to climb aboard. By saving a few dollars, you get to risk slipping and falling on your face.

A winged, bulbous keel? Ought to be fun trying to get unstuck when you  run aground in this one. Especially in mud. The bottom of the thing is shaped like a giant suction cup. A winged keel made of cast lead? Wow, what a great idea! Oh, well, maybe you'll have fun hammering it back in shape every time you run aground. Does that oddly shaped hunk of lead reduce resistance and makes it go faster, too? Not likely. But it certainly had the effect of making her unusually tender. You notice that the moment you step aboard.   Heading around a sharp bend in the river under power, the boat heeled over at least 20 degrees, which I thought was ridiculous. It may stiffen up under sail, but with a complete lack of wind, we didn't get to find out.  Fads are cool, until you find out that's all it is.

Unfortunately, there were other problems that continue to prove the point that very low cost usually translates to very big problems. It was not until she was hauled that we could understand why this boat sells at such a low price. The fiberglass content of the hull is about as little as it could be without falling apart. The hull bottom was so thin that it  frightened me. In just about any place there wasn't a frame, you could push in the bottom with your thumb. Tapping on it with a hammer, it would vibrate. In the unsupported aft quarters, it dimpled as easily as an oil can. Granted, there were no signs of immanent structural failure, or even stress cracks on the bottom. But everything I saw on this boat suggested that it hadn't been used much,  so I doubt that the hull has ever been seriously stressed.

Some people don't think that a weak hull on a boat is much to be concerned about. The attitude is that as long as it doesn't fail under normal conditions, then its okay. My view on that is that people who hold that attitude have never been out to sea in a storm. I've sail raced all over North American, and I've seen my share of hull failures, including some that have cost lives. In one case, a knock down with the spinnaker up resulted in the deck pulling right off the hull. In another, the hull side caved in when hit by a wave broadside. And these boats were built far better than the Hunter 28. Of course, many people rationalize by saying that they only go sailing on nice days. Okay, its you're life. But add to this the fact that this very thin bottom was badly blistered and you have plenty of reasons to take a pass on the Hunter 28.

The list grows a bit longer when we discuss the large soft spots found in the rudder, but we have no idea what's going on there, just that its getting a little mushy. We might surmise that like a lot of rudders, its just some fiberglass laid over a foam core, as a lot of cheap rudders are.  We can add to the long list of Yanmar diesels with flubber engine mounts that are so soft and loose that the engine does the Watusi when you start it up. An engine that won't hold still and oscillates by as much as 1/2" is going to cause damage to the drive system sooner or later. Start with rapidly wearing cutlass bearings and packing glands and graduate eventually to transmission damage.

There are no gauges for the engine, and the control panel is down near the bottom of the cockpit where you can easily reach it by bending over in a space where there's not enough room to bend over. Why builders continue to place the engine controls in locations like this just beyond me. I guess the scuppers will never get plugged up and that electrical stuff will never get wet. At the bottom of the cockpit. The plastic throttle level on the steering pedestal felt like it was going to break off in my hand, it bent so much. Then there is a   plastic fuel tank  held in place with packaging straps and steel clips that will rust and fall apart as soon as they get wet a few times. The boat comes with a Mayfair bilge pump that is smaller than most coffee cups, and the single, small  12 volt automotive battery is sure to keep it running for a long time. Of course, small boats never get big leaks, so why worry?  This is getting kind of sad, isn't it?

Anyone who peruses the various sailing publications these days can't help but notice the inordinate number of boats that are either breaking apart or being dismasted, as well as the increasing number of fatalities. Instead of using the word dismasted, which implies the connotation of some external force as the cause of the dismasting, perhaps I should just say "masts falling down." Far too many of these dismastings ARE simply a matter of ultralight rigs toppling over because the designer pushed the safety margin to the limits, or beyond. Its not the weather conditions that were the cause; no, its hot shot design that pushes the bounds of sensibility. Far too many rudders and keels are falling off, deck joints separating and hulls splitting open. The average weekend sailor, lacking much heavy weather experience, has no idea of the terror he may be in for when he makes the mistake of venturing far from shore in what is nothing more than a day sailor. Those of you who get ideas about "bluewater voyaging" in a bargain boat like this would do well to reconsider that the ocean remains a dangerous place.

This could have been a nice, well-made boat. Parts of it are, but the builder didn't have his priorities straight. If all you're going to do is sail around the pond on balmy days, its probably fine for that. A serious deep water sailor she's not.  This is a price boat, and there's altogether too much that you don't get for what you don't pay, for any serious sailor to take the Hunter 28 seriously. There's a good reason why first impressions should be taken seriously, too. What you don't pay for up front will surely be heavily loaded on the back end. Count on it.

If  you wonder why people are leaving sailing like the plague just arrived, possibly this boat offers some reasons. There are too many just like it.

Posted August 1, 1998

David Pascoe - Biography

David Pascoe is a second generation marine surveyor in his family who began his surveying career at age 16 as an apprentice in 1965 as the era of wooden boats was drawing to a close.

Certified by the National Association of Marine Surveyors in 1972, he has conducted over 5,000 pre purchase surveys in addition to having conducted hundreds of boating accident investigations, including fires, sinkings, hull failures and machinery failure analysis.

Over forty years of knowledge and experience are brought to bear in following books. David Pascoe is the author of:

• " Mid Size Power Boats " (2003)
• " Buyers’ Guide to Outboard Boats " (2002)
• " Surveying Fiberglass Power Boats " (2001, 2nd Edition - 2005)
• " Marine Investigations " (2004).

In addition to readers in the United States, boaters and boat industry professionals worldwide from nearly 80 countries have purchased David Pascoe's books, since introduction of his first book in 2001.

In 2012, David Pascoe has retired from marine surveying business at age 65.

On November 23rd, 2018, David Pascoe has passed away at age 71.

Biography - Long version

Boat Reviews Articles At-A-Glance

• Introduction to Boat Reviews
• Albemarle 305
• Aquasport 215
• Baha 260 Targa (not "Baja")
• Bertram Yachts
• Bertram Yachts: Introduction
• Bertram 26.6 II
• Bertram 28 II
• Bertram 30 Express
• Bertram 30 Moppie
• Bertram 31 SF
• Bertram 33 SF
• Bertram 36 Moppie
• Bertram 42 Convertible
• Bertram 46 Convertible
• Blackfin Yachts
• Blackfin 29 SF
• Blackfin 29 Combi
• Blackfin 32 Flybridge
• Blackfin 33
• Boston Whaler Outrage 26
• Cabo 31 Sport Express
• Century 3000
• Chris-Craft 302 Crown
• Contender 25
• Cranchi Mediterranee 40
• Cruisers 4270 Esprit
• Cruisers 4280
• Glacier Bay 2640 Renegade
• Grady-White Offshore 24
• Grady-White 24 Voyager
• Grady White 272 Sailfish
• Grand Banks 42
• Gulfstar 43  Trawler-style Yacht
• Hatteras Yachts
• Hatteras Yachts: Introduction
• Hatteras 36 Convertible
• Hatteras 38 Convertible
• Hatteras 38 Convertible - Updated Review
• Hatteras 39 Sport Express
• Hatteras 45 Convertible
• Hatteras 52 Convertible
• Hatteras 53 Motor Yacht & Convertible
• Hatteras 61 Motor Yacht
• Hyatt 45 CMY
• Intrepid 289
• Island Gypsy 40
• Legacy 34 Express
• Luhrs 320 Open
• Luhrs 34 - 340 F.B. Sedan
• Luhrs Tournament 350
• Luhrs Tournament 360
• Mainship 31
• Mainship 350 Trawler
• Mako 221- Updated 11/05/99
• Maxum 4600 1998
• Morgan 462 Ketch
• Offshore 48
• Post 46 Convertible
• Pursuit 2855
• Pursuit 3000 Offshore
• Pursuit 3070 CC
• Sea Ray and Balsa Core Bottoms (from "Structural Issues")
• Sea Ray 250 Sundancer
• Sea Ray Sundancer 290
• Sea Say Sundancer 290 Update
• Sea Ray 370 AC
• Sea Ray 39 Express
• Sea Ray 500
• Shamrock 26
• Thompson Santa Cruz 2700
• Tiara Yachts
• Tiara Today
• Tiara 3100 Open
• Tiara 3600 Convertible
• Tiara 3600 Open
• Topaz 28_1981
• Trojan 10-8 Meter
• Trojan 14 Meter Convertible
• Trojan 440 Express
• Viking 43 Open
• from Buying a Boat cat.
• Marlin Monroe 42 Bertram Convertible Make an Old Boat New
• A Few Favorites

• Basic Considerations
• Boat Types: Which is Right for You?
• Old Boats, New Boats and Quality
• Basic Hull Construction
• Evaluating Boat Hulls
• Performance and Sea Keeping
• Decks & Superstructure
• Stress Cracks,Finishes and Surface Defects
• Power Options
• The Engine Room
• Electrical & Plumbing Systems
• Design Details
• Steering, Controls, Systems & Equipment
• The Art of the Deal
• Boat Shopping
• The Survey & Post Survey
• Boat Builders by Company

• What is Pre-Purchase Survey?
• Business Practices and Client Relations
• Sound vs. Seaworthiness
• Hull and Its Structure
• Surveying the Hull
• Using Moisture Meters
• Stress Cracks & Surface Irregularities
• Deck & Superstructure
• Drive Train
• Gas Engines
• Fuel Systems
• Exhaust Systems
• Electrical Systems
• Plumbing Systems

Published by: D. H. Pascoe & Co., Inc. Articles, Images: Copyright © 1997 - 2018 David H. Pascoe All rights reserved. Articles, Images: Copyright © 2019-2022 Junko A. Pascoe All rights reserved. Web site design & developement: Copyright © 1997 - 2023 Junko A. Pascoe All rights reserved. Web site: Maintained by Junko A. Pascoe

HUNTER 28 Detailed Review

If you are a boat enthusiast looking to get more information on specs, built, make, etc. of different boats, then here is a complete review of HUNTER 28. Built by Hunter Marine (USA) and designed by undefined, the boat was first built in 1989. It has a hull type of Wing Keel and LOA is 8.54. Its sail area/displacement ratio 16.82. Its auxiliary power tank, manufactured by Yanmar, runs on Diesel.

HUNTER 28 has retained its value as a result of superior building, a solid reputation, and a devoted owner base. Read on to find out more about HUNTER 28 and decide if it is a fit for your boating needs.

Boat Information

Boat specifications, sail boat calculation, rig and sail specs, auxillary power tank, accomodations, contributions, who builds hunter 28.

HUNTER 28 is built by Hunter Marine (USA).

When was HUNTER 28 first built?

HUNTER 28 was first built in 1989.

How long is HUNTER 28?

HUNTER 28 is 7.37 m in length.

What is mast height on HUNTER 28?

HUNTER 28 has a mast height of 11.43 m.

Member Boats at HarborMoor

Great choice! Your favorites are temporarily saved for this session. Sign in to save them permanently, access them on any device, and receive relevant alerts.

• Sailboat Guide

1992 Hunter 28

• Description

Seller's Description

The owner bought this boat in 2001

General condition and any additional information

Well maintained 1992, 28 foot Hunter sloop. Freshwater Boat.

Very, very clean

Standard features

Rig includes Roller reefing jib, double spreader fractional rig, two speed self tailing sheet winches, self tailing halyard winch, six rope clutches, internal halyards, mid-boom sheeting, adjustable mainsheet traveler, inboard genoa tracks with cars and boom vang. Sail inventory includes two mainsails, 100% jib and 140% genoa.

Interior amenities include: full set of interior cushions, a fresh water tank, hot/cold pressurized water system that runs on either 120V AC or while engine is running, fully enclosed bathroom for privacy, with a full shower and fully-functional head with sanitary holding tank, spacious captains berth and v-berth, two bunks, built-in cooler, and 2-burner alcohol stove, and pop-up table. Has both AC and DC electrical system.

Yanmar Marine Diesel Engine 2GM20F, 18hp with Dr. Fuel fuel filter. Fuel tank is 18 Gallons. Engine is in excellent condition, low hours per year.

Extra gear included

Miscellaneous gear to be included; Anchor, chain and rode, shore power chord, winch handles, oil removal pump, five gallon, diesel fuel can, two mainsail covers, dock fenders, life jackets (four, orange), hatch and companionway screens, manuals, misc. tools.

Note: Hot water tank has sprung a leak and has been bypassed.

Improvements to the hull, deck, rigging, engine, or interior

Pedestal steering. Instrumentation includes Signet Marine SL250 Depth / knot meter, Raymarine wheel pilot, Bulkhead compass, VHF radio and two batteries.

VC-17 antifouling bottom paint and custom steel cradle

Rig and Sails

Auxilary power, accomodations, calculations.

The theoretical maximum speed that a displacement hull can move efficiently through the water is determined by it's waterline length and displacement. It may be unable to reach this speed if the boat is underpowered or heavily loaded, though it may exceed this speed given enough power. Read more.

Classic hull speed formula:

Hull Speed = 1.34 x √LWL

Max Speed/Length ratio = 8.26 ÷ Displacement/Length ratio .311 Hull Speed = Max Speed/Length ratio x √LWL

Sail Area / Displacement Ratio

A measure of the power of the sails relative to the weight of the boat. The higher the number, the higher the performance, but the harder the boat will be to handle. This ratio is a "non-dimensional" value that facilitates comparisons between boats of different types and sizes. Read more.

SA/D = SA ÷ (D ÷ 64) 2/3

• SA : Sail area in square feet, derived by adding the mainsail area to 100% of the foretriangle area (the lateral area above the deck between the mast and the forestay).
• D : Displacement in pounds.

Ballast / Displacement Ratio

A measure of the stability of a boat's hull that suggests how well a monohull will stand up to its sails. The ballast displacement ratio indicates how much of the weight of a boat is placed for maximum stability against capsizing and is an indicator of stiffness and resistance to capsize.

Ballast / Displacement * 100

Displacement / Length Ratio

A measure of the weight of the boat relative to it's length at the waterline. The higher a boat’s D/L ratio, the more easily it will carry a load and the more comfortable its motion will be. The lower a boat's ratio is, the less power it takes to drive the boat to its nominal hull speed or beyond. Read more.

D/L = (D ÷ 2240) ÷ (0.01 x LWL)³

• D: Displacement of the boat in pounds.
• LWL: Waterline length in feet

Comfort Ratio

This ratio assess how quickly and abruptly a boat’s hull reacts to waves in a significant seaway, these being the elements of a boat’s motion most likely to cause seasickness. Read more.

Comfort ratio = D ÷ (.65 x (.7 LWL + .3 LOA) x Beam 1.33 )

• D: Displacement of the boat in pounds
• LOA: Length overall in feet
• Beam: Width of boat at the widest point in feet

Capsize Screening Formula

This formula attempts to indicate whether a given boat might be too wide and light to readily right itself after being overturned in extreme conditions. Read more.

CSV = Beam ÷ ³√(D / 64)

Thanks to Phil Galbiati for providing information on this boat. Update of the HUNTER 28.5 (1985-1988).

This listing is presented by SailboatOwners.com . Visit their website for more information or to contact the seller.

View on SailboatOwners.com

Embed this page on your own website by copying and pasting this code.

• About Sailboat Guide

©2024 Sea Time Tech, LLC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

• Forums New posts Unanswered threads Register Top Posts Email
• What's new New posts New Posts (legacy) Latest activity New media
• Media New media New comments
• Boat Info Downloads Weekly Quiz Topic FAQ 10000boatnames.com
• Classifieds Sell Your Boat Used Gear for Sale
• Parts General Marine Parts Hunter Beneteau Catalina MacGregor Oday
• Help Terms of Use Monday Mail Subscribe Monday Mail Unsubscribe

What is the best 28 ft for the money

• Thread starter Gordon Shadburne
• Start date Nov 11, 2004
• Forums for All Owners
• Ask All Sailors

Gordon Shadburne

I am looking for the best- family (not racing) sailboat 28 ft (or so) for 10,000-13,000Now live in Portland,Or. will be moving to Pudget Sound- WA.area. Want it safe!,big cabin (wife has some kneee problems) good mataince record. Am missionary to Native Americans ( www.warriorsforchristonline.org ) so limited in funds-Need your input- thanksGordon/WFCps now only have a 14 ft C-lark/ sail it sence 1970-  

mike C16582

i'm biased, but.......... As I said, I'm biased, but if you can find an O"day 28 I think you'll be happy. However, $10,000-$13,000 is cutting it close. AS a matter of fact, there's an O"Day 28 for sale right now in Portland Or. for $12,900 (I'm sure the price is negotiable)here's the link for it..........http://www.yachtworld.com/core/listing/pl_boat_detail.jsp?currency=USD&units=Feet&checked_boats=1309615&slim=quick&  

Newport 28 Hello,Mike own's and likes O'day, I own and like Newport. Newport's were made in California, so lots should be available on the west cost.Compared to O'day, the Newport has a double berth in the cabin (the port sette slides out). Also, all Newport come with the traveler mounted on top of the companionway. Most Newports come with hot water, fresh water cooled diesel, and some other things as well.As far as I can tell, both the Newport and the O'day are good boats. Good luck,Barry  

John Dawson

Cal 29 or 27 probably fall into this price range, and less if needing work. Large cabins, good performance, good reputation.  

Hunter 27 for two The Hunter 27 built from 75-84 to a design by John Cherubini is just the right size for a couple. It's a seaworthy design, with 6 feet of headroom in the cabin. The bench seats in the cabin make very comfortable bunks (easily reached by stiff knees.) The ride is comfortable in a seaway, and the cockpit is comfortable, with good back support. Ours was easily rigged for single handing, so the Admiral does not need to go on deck.And the price is right - $9,000 to $12,000 will get you going. (Ours '77 cost $9,000 and was ready to sail.) At your size and price parameters, you will end up with a "good old boat" and the associated maintenance work. Do get a survey to be sure you are not buying a project, and enjoy cruising!DavidLady Lillie  

Pearson 26-28 I learned how to sail at the boston harbor sailing club where they have a fleet of pearson 26 and 28's. The members sail these boats in all kinds of new england weather through a busy harbor and scatterred islands. They are built tough sail between 5 and 6 knots, have thick fiberglass hulls and seldom break down.  

Go for a Catalina 27 *! I realize the Catalina 27 isn't a 28 footer, but I think it would be a good match for your needs. They are plentiful, within your price range, have a large cockpit, seaworthy, and have nice sailing characteristics.If you could spend the extra $5K, the O'Day 28 is a better boat - faster (but can pound), and very well finished.Having owned both boats, if price is the biggest constraint, go with the C27.-Mark  

Stu Jackson

Augie byllott.

Comfortable boat for a couple Is there anything compelling about 28'?I recently sold a 1978 Catalina 30 after enjoying it for 15 years. Those additional two feet move the comfort level light years above the Catalina 27 owned by one of my friends. The cabin fever that one may experience on a smaller boat vanishes on the C30. A larger head, vee berth, saloon, dinette, and cockpit make a world of difference where a woman's comfort is concerned.With more than seven thousand having been built, there are always hundreds of C30s on the market. With a little horse trading and jawboning, you might be able to find one in your price range.It's worth a try.If anything, I believe that a C30 is easier to sail than a C27.  

Thanks for your response Thanks for your comments. Condsidering they aren't making them anymore, do you think there are problems getting parts for the Newports?I have read that the O'day stiffens in higher winds and is more forgiving when you get into troubling times. How would compare the Newport as far as safety and structural quailty and durability?  

Newport Info Hello,A great site for Newport Info is here:http://webhost.sailnet.com/newport/index.htmlRegarding parts availability, one thing I have learned is that most parts on a sailboat don't come from the original manufacturer. For example, the engine is from Universal diesel, the steering is Edson, the winches are Lewmar, the headsail roller furler is Profurl, the bilge pump is rule, the .....What did come from from the manufacturer you can now get from the aftermarket. O'day, Pearson, CnC (for a while anyway) all went out of busines. Hunter and Catalina are still in business, but I don't think you can still buy a rudder or something like that for a Catalina 27.Good luck,Barry  

Pearson 28 HI Gordon,Don't rule out the Pearson 28. The models made before 1982 can be found quite reasonably. This boat was built very well, is strong, safe, roomy and very easy and fun to sail. We owned one for 4 years and loved it. You can get one in the price range you mention. Go to yachtworld and check them out.Joanie  

Hunter 28.5 We have an '88 model. VERY well built, no blister problems. Taken her on 3-week trips on Lake Michigan covering some 600 miles total. Have been in all kinds of weather with her and she's always brought us home safely. I often single-hand her as well.  

Hunter 28.5, Pt II I, too, own a Hunter 28.5 (1986 model). While I think Hunter packed a lot of value into this model boat, I don't think you could find one in very good condition for your price range. I do think you could find one for just a bit more (say around $15k), but you'd probably have to put some work into it and perhaps buy some new sails. I personally believe that the 28.5 is a great boat for single-handling, coastal or river/lake cruising with a small family in a semi-protected environment, or similar sailing. But in the price range you mention, most of the listed 28 or so footers are going to be in the 1978-1982 or so age group. Any boat that is 25 or so years old needs to be VERY carefully inspected, by you and a professional surveyor as it could be subject to a number of conditions that could be expensive or prohibitive to repair. In the interim, you may want to take a look at Don Casey's book "Inspecting The Aging Sailboat." It will give you a better sense of how to evaluate some of the candidate boats you may look at. It's a buyer beware world out there....  

Gordon, The best 28 is a Catalina 28 and because of that they are very expensive. The next best and most boat for the money is a Hunter 28... not a Hunter 28.5. The Pearson 28 is the next best followed by the Hunter 28.5.The main reason for the rating is the walk through swim platform offer by both the Catalina 28 and the Hunter 28! Great for the family getting on and off the boat and into the water. The construction of the Catalina is better than the Hunter. The Pearson construction is also better than Hunter. I own a Hunter 28 and love the boat! I took a long time reviewing which boat to buy. Everyone will tell you they love thier boat. I do too but a Catalina is better!  

This thread could go on for ever We all bought our current boat for one reason or another price,walk through transomes,loyalty to the brand and so on and we all could come up with reason's as to why. So asking a question like the best 28 footer for the money and you will get a different answer from each of us. So it is not really a fair question to ask because your best 28 footer for the money may not be mine. Taken in what your needs are all the boats mentioned would work. They are all great boats and have ther good and bad. But it all comes down to YOU and the $$$. Keep in mind that in this price range you will be buying a 30 year + boat. That will need upgrades and might have a gas engine or an out board. Look for the right deal and keep in mind the survey could eat up 5% of your boat money. So it is tough to say which boat is the best for you and your needs. Also keep in mind that your wife will need to climb all over the boat and up and down into the cabin bad knees and all. So a boat with wide side deck's might be a consideration over a boat with narrow side decks. Plus the climbing of the steps of 5 or 6 steps to get down below. It will really comne down to looking at allot of boat's and seeing which boat fit's the needs. Your price range will limit you and might force you into buying a older boat than maybe you had thought and also throw in the location. Boats on the West Coast seem to bring more for the same boat on the East Coast. Cliff  

Finding and buying your boat Having contributed my 2 cents on our own model, here is my recommendation on how to buy a boat:In your price and size range, you are loooking for a "good old boat." Many of us own these great models from the 70's and early 80's. In general, they have great cruising designs, overbuilt hulls (because this was before anyone really understood fiberglass), and may involve some maintenance. (Although we sailed Lady Lillie through her first summer, 500 miles, and 22 nights on board as we bought her.)Look at lots of boats in your price range. This will be the hardest part for your wife's knees, but after a while you will settle on a few designs you like, and you can look without her until you find the one you want. Lay down in all the berths you might use. Sit in the cockpit. Stand in the galley, and go through the motions of preparing food and washing dishes. Sit on the head. Go forward from sitting in the cockpit along the decks to the bow. Don't worry about the model, you will figure out which ones you like. Consider using a local agent who is supportive of your wishes (not trying to seelyou up to a higher price,) and can arrange to get you on a lot of boats.Buy one of the good books on this site that describe how to buy a cruising sailboat. Read the reviews on this website. 28 footers were not commonly built in the '74-'85 range you need for your price, so look at the 27 and 30 footers. The boats for sale on this and other sites can get you started, and help you understand pricing.Find _your_ surveyer. Ask other sailers who is the most competent and trustworthy in your area. This is imporatnt because a good survey allows you to understand 80% to 90% of the maintenance you will be doing in the first years of boat ownership. You contract must include the survey, and your right to walk away or negotiate a price reduction based on the survey results.Take your time. Many boats will come on the market in the next six months, and you can find the one with just the characteristics you want and like.Our search took about 6 weeks during which we climbed into about 10 boats on the hard (and in the ice and snow.) We came down to a choice between a Catalina 30 at $18,000, and a Hunter 27 at $9,000. We checked with the marina near our house, and they said that the 5 1/2 foot draft of the Catalina was too deep for the marina. We bought the '77 Hunter 27, and have loved her.The cabin has headroom to 6 feet. The diesel will drive us all day through calm seas, but is a little small if we are bucking wind and waves (something we try always to plan, or wait around.) There is plenty of room and comfort for the Admiral and me. We sleep in the v-berth, where 5' 11" and 5' 8" means that we play footsie occasionally, but are both very comfortable. The bench berths in the main cabin easily and confortably accommodate my two brothers who go a large 6' 2". The accommodations are ideal for me and my wife. We have spent two weeks on her, and could easily go a month. Although tight and familiar, my Dad, brothers and I have cruised a week on her, and we are quite comfortable. I believe that we would have been just as happy on the Catalina 30, but shoal draft is a real value for some of the ports, and anchorages of Lake Erie when the water is low. I really don't believe there is any clear choice of one model. Any of those mentioned so far (and a number of others) could be your boat.Your boat is out there, near you. Educate yourself, and invest in climbing aboard enough to find the fit for you. If the workmanship is good enough to last 20 to 30 years, and pass your survey, you don't have to worry about your time on her. Do it, you will love the joys of cruising - anyway, we do.DavidLady Lillie  

Plan for incidental costs If your budget is tight, look out for the costs that you may have in getting your boat to its new home and making it yours. In addition to the survey and cost of a sea trial (we paid for a marina worker to sail the boat at the sea trial), we paid to have the mast taken down, truck to our lake, put the mast up. Altogether, it was about $1,800 with survey and sea trial included.We bought a 27' Starwind (1984) and then put another $1,400 into re-upholstering everything, including new foam for all cushions. Then I needed to replace a halyard and a main sheet, buy new dock lines and hardware for the slip, another $400 at West Marine for stuff, new sails maybe next year ... you get the picture.We looked at about 8 boats over a couple weeks and we were anxious to find one before the summer ran away from us this year. We noticed a big difference in the comfort factor between the Cal 2-27 and our boat compared to the others which were all 26' or less. So you are certainly looking for the right size.You can put a lot of emphasis on all the practical elements of a boat, but for me, it mainly comes down to how does she make you feel to look at her for the first time (and every other time thereafter). Everytime I look at her, I'm happy with what we bought. I don't think you can be happy with a boat if you don't feel that emotion. Then, you just better be prepared emotionally to walk away if the survey reveals problems that you're not prepared financially to overcome.My wife and I had that feeling for 2 boats ... first for the Cal, which slipped away because we didn't make an offer quick enough. We looked longingly at ads for a few Catalinas that were just out of reach for what we wanted to spend on our first boat.Luckily, I think we are very happy with the Starwind because it has many features and layout differences that make it a better boat for us.Take a good look around, use as much time as you need ... when you find her, you'll know it!  

Seafarer I have 2 Seafarer 30 footers. They were designed by McCurdy and Rhodes in 1978. Its a VERY safe, heavy duty and large for its length boat. There is a very good and active forum for these (one reason I bought one).I want to sell one (I bought the 2nd one for the trailer it was on and the 9 sails that came with it as well as having a back up in case I needed anything).The boat was one of the few to survive Ivan intact, and with no damage to it (except rubrail scuffing). The owners group had a mould made for the rubrail, so a new one is available inexpensively.It has a 23 hp Volvo 2 cylinder diesel that has 360+ or- hours, and looks almost new(the engine and tranny).The baot needs a good cleanup (from being stored and unused) recover upholstery, varnish brightwork, etc and the installation of the engine (i would do for additional cash).I want $4500.00 for it, as is.Look at yachtworld for Seafarer Swiftsure 30. Also compare hullspeed, quality of construction, and owners comments. This is a GREAT deal and very safe if you don't mind cleaning a little and upholstering it to your wifes tastes.let me know if interested.Tommy[email protected]  

What about the Columbia 8.3? Any reason the Columbia 8.3 wasn't mentioned? This appears to be a well built cruiser/club racer that should be in the price range.  

• This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. By continuing to use this site, you are consenting to our use of cookies. Accept Learn more…

Hunter Sailboats For Sale

5 listings found.

36 Hunter Vision 1993

Freshwater Only – 1989 Hunter 33.5 Sloop-Rigged Cruiser, Shoal Wing Keel

1978 Hunter 30 Cheurbini

Hunter 44 DS perfect to live aboard!

Hunter sailboats for sale on sailtrader, new hunter sailboats.

New hunter sailboats for sale come in a range of sizes for any sailor to enjoy. New Hunter sailboats are designed for stability and conformable performance. New designed Hunter’s have well-thought deck layout making it simple to sail shorthanded. 

Three new Hunter sailboat categories are: tailorable daysailor (15-20 ft), midsize keelboats (31-37 ft), large keelboats (40-50 ft). New hunter sailboat prices range from $10,123 for a 15 ft daysailor to $433,985 for the new 50′ center cockpit model. Prices can vary for each model depending on the options chosen by the buyer.

Used Hunter Sailboats

Find a range of used Hunter sailboats for sale on SailTrader with photos, prices and details from private sellers and dealers. For over 40 years Hunter has been manufacturing sailboats in North America which created many opportunities for sailors to find used Hunter available to buy.

SailTrader is a popular destination for sellers to list their Hunter sailboats for sale. Find used Hunter sailboat prices, photos and complete selling information. If you don’t find the information you’re looking for to buy, contact the seller for details.

Sailboats Privately Listed

SailTrader is the leading website for privately listed Hunter sailboats for sale. Many sailors often choose to sell their sailboat on their own. Sellers can easily create an account, list sailboat details, add photos and get contacted to potential buyers.

Hunter Sailboats For Sale by Dealer

With Hunter sailboats being as popular as they are, shoppers will often find Hunter sailboats for sale by dealers. Hunters are design to be enjoyed by a wide range of sailing skill sets. From weekend cruising to Wednesday night racing, a dealer can help you find the right Hunter sailboat for sale with the feature you need. With Hunters sailboat long history of sailboat manufacturing in North America there have been many different designs throughout the years. A dealer can help you navigate  sailboats with complicated systems.

Sell Your Hunter Sailboat

Aside from selling Hunter Sailboats, SailTrader encourages sailors looking to sell their Hunter sailboat to list them here too. It’s easy to do. Anyone can make a SailTrader account the and list a sailboat for sale.

The Sailor’s Marketplace for Sailboats and Sails.

Sell Your Sailboat

Sailboats for sale.

• New Sailboats
• Used Sailboats
• Cruising Sailboats
• Racing Sailboats

Sell Your Sails

Sails for sail, sail manufacturers.

• North Sails
• Quantum Sails
• Doyle Sails
• UK Sailmakers

Sailing Reviews

• Sailing Line
• Safety Equipment
• Sailing Accesories

As an Amazon Associate SailTrader earns from qualifying purchases.

This website uses cookies to ensure you get the best experience possible. 

• Sign In or Register
• Boats for Sale
• Research Boats
• Sell a Boat
• Search Alerts
• My Listings
• Account Settings
• Dealer Advertising
• 28 Foot Sailboat

28 Foot Sailboat Boats for sale

1984 O'day 28

Douglas, Michigan

Make O'day

Category Sloop

Posted 1 Month Ago

The hull was painted in 2020 and is serviceable, the deck is firm and the surface is shiny. The wooden brightwork needs a seasonal surfacing. There is no evidence of water infiltration around portholes or through bolts. The Engine was replaced with a rebuilt Kubota M12 in August 2018. The sails are reported to be in working order and the general condition of the vessel is better than average. The interior is in very good condition. Stock #290853 Sail Tomorrow! Made for comfort and Style, this 1984 28' O'day sailboat is Ready Today to set sail O'Day sailboats are well made, great for sailing and light on brightwork maintenance requirements, and this 1984 28 is no exception. Designed by C. Raymond Hunt this 28-foot sailboat is made for roominess and style. Its layout is classically symmetrical. The cabin can hold six people comfortably. The cockpit can easily hold that many or more. The O'day 28's forgiving nature and easy stability make this boat for sailors new to boat ownership or the more experienced, an easy choice. The cockpit has cushions, in serviceable condition, on the back and both sides with cup holders by the wheel. and GPS and compass at the helm. Powered by a Kubota M12 diesel engine with 10 HP will get you anywhere a breeze cannot take you. The galley has a sink, a microwave, a two-burner alcohol stove. butcher block countertops, and a large ice bucket area under counter. There is plenty of storage above the counter. The dining area has U-shaped benches that convert to a bed and a large settee across from the dining table. The O'Day has an aft sleeping area that also has an access door to the engine compartment. A more open second engine access area is easily accessible underneath stairs. The fore V-berth has ample sleeping space for two with padded walls and storage underneath and a wardrobe closet and drawers across from head and has a door for privacy. The head is starboard side midships and has toilet, sink, and shower with a door for privacy. Plenty of storage throughout with cubby holes and storage cabinets. The sale includes a 10' 2" dinghy with gas powered outboard, a deck box, a cradle and manuals for boat and engine. A 100% jib, mainsail, rigging, and a 25 lb CQR plow anchor are included. Let the wind take you where you want to go. Reason for selling is unable to manage.

1982 S2 8.5A 28 foot Sailboat with Inboard Yanmar Diesel - In Racine Wisconsin

Racine, Wisconsin

Category Cruiser Motorcycles

Length 28.0

Posted Over 1 Month

**** PLEASE NOTE: Because of the relatively low BUY IT NOW price, payment will be due within 24 hours via paypal. I will send you a paypal invoice after a successful "BUY IT NOW" or an accepted offer. Please only buy or offer if you have positive feedback. Your buy it now or offer constitutes a binding agreement to purchase so please ask questions BEFORE clicking "BUY IT NOW" or making an offer. After receiving your payment I will overnight you the title or meet you in person depending on timing and my availability.**** Very Nice S2 8.5A (28ft) for sale in Racine Wisconsin. I'm expecting a second child soon and really don't want to sell this excellent great lakes cruiser. Clean and clear Wisconsin title.Tiller steering. (always my preference)Inboard Yanmar diesel is extremely clean and fuel efficient. Recent full Yanmar service checkout since boat was last launched.Furling headsail in good shape. Newer mainsail in excellent shape.New Raymarine autopilot professionally installed. Shore power and long power cable. Halyards in good shape.New marine head and holding tank (never used). Chainplates recently professionally rebedded by boatyard. Interior in excellent shape.Solid fiberglass hull. All tabbed in joinery in excellent shape. Cored deck with NO soft spots. Very large cockpit.Includes steel cradle as well. I looked at everything in this size and price range in the lower half of lake Michigan for two years and this is the nicest boat I could find by leaps and bounds. Solid turnkey value. Launch is all ready paid for with the boat yard. You can be in the water tomorrow. No better deal can be found on solid and ready to sail Great Lakes cruiser with a clean inboard diesel - it is just time for me to move it along. Currently out of the water at Racine Riverside Marina in Racine, WI. Summer storage is paid through the end of this month and a launch is included in the purchase. If you chose not to launch until next season the storage rates at the Marina for winter are extremely reasonable and the pre-paid launch will still be yours come next summer. Here is a Review from "Practical Sailor" S2 8.5 MeterThe 8.5 is good for cruising the coasts in comfort and style--as long as you like the modern look.When Leon Slikkers founded S2 Yachts in 1973, much of the attention to detail that had previously characterized Slickcraft powerboats—Slikkers’ earlier boatbuilding venture— traveled with him to the new boatbuilding company. In the 13 years S2 sailboats were in production (S2 still makes powerboats), the company produced a variety of modern cruising designs from the board of Arthur Edmunds, all characterized by longish fin keels, freestanding spade rudders, straight sheerlines, and a staggering variety of draft options and cockpit locations. In the early ’80s, S2 reached more for the performance market with the Grand Slam series of small boats, and the 10.3 “offshore racer-cruiser.” These higher performance boats were designed by Scott Graham and Eric Schlageter, well known for their MORC and smaller IOR designs.The S2 8.5 is a 28-footer cast in the company’s traditional mold. Her hull dimensions, sail area, displacement, and general design characteristics put her square in the middle of the modern 28-footers such as the Tanzer 8.5, Newport 28, O’Day 28, and the Pearson 28.The boat’s styling is conventionally modern. She has a fairly straight sheer, fairly high freeboard, and low, raked cabin trunk with dark tinted flush ports. Production of the 8.5 ran from 1981 to 1983. The boat was replaced by the similar S2 8.6, which continued until S2 stopped making sailboats in 1986.ConstructionThe hull of the S2 8.5 is a solid hand layup. Glasswork is excellent, and is noted by owners as one of the main considerations in buying the boat. Gelcoat quality is excellent.Slight roving printthrough is evident, but it is not objectionable. Minor hard spots are visible in the topsides, probably caused by the attachment of interior furniture and bulkheads.The deck molding is cored with end grain balsa, giving a solid feel underfoot as well as providing reasonable insulating properties.S2’s hull-to-deck joint is the basic type that we would like to see adopted throughout the industry. The hull molding has an inward-turning flange, onto which the deck molding is dropped. The joint is bedded in flexible sealant, and through bolted on six inch intervals by bolts passing through the full length slotted aluminum toerail. The joint is also through bolted across the stem.All deck hardware is properly through bolted, although pulpits, cleats, and winches merely use nuts and washers on the underside of the deck, rather than the aluminum or stainless steel backing plates we prefer.Another feature of the hull-to-deck joint is a heavy, semi-rigid vinyl rubrail at the sheerline, quite aptly termed a “crash rubrail” by S2. This will go a long way toward absorbing the shock of the inevitable encounters with docks and the other hard objects that seem to be attracted to the topsides of the typical sailboat. Although this rail is black when the boat is new, it had dulled to a chalky gray on older S2’s we examined.The builder advertises “bronze seacocks on all through hull fittings.” These are not traditional tapered plug seacocks, but are ball valves mounted directly to through hull fittings. A proper seacock—whether it uses a ball valve or a tapered plug—has a heavy flange to allow through bolting to the hull. This is an important safety feature. Should a valve seize, it may become necessary to apply a great deal of leverage to the handle in order to open or close the valve. The deeply threaded through hull stem can easily break under these conditions, and more than one boat has been lost in this manner.We also suggest that seacocks be installed on the cockpit drain scuppers and the bilge pump outlet, both of which may be under water while the boat is sailing. Light air performance would benefit by the fairing in of the through hull fittings, particularly the head intake and discharge, both of which are far enough forward to have a significant effect on water flow past the hull.Ballast is a 3,000 pound lead casting, epoxied inside a hollow keel shell. We prefer an external lead casting bolted to the hull for its shock-absorbing qualities and ease of repair. This preference was reinforced recently when we examined an old Bristol 27 just sold by a friend. The surveyor noticed dampness near the bottom of the leading edge of the keel, which showed slight external damage. Probing the loose putty revealed some abrasion of the glass keel molding. In order to sell the boat, it was necessary to grind away a large portion of the glass at the front of the keel, dry out the ballast, and reglass the lead—a job that took several days of work and cost our friend a fair chunk of money.Much of the boat’s interior structure is plywood, glassed to the hull. Fillet bonding is neat and workmanlike with no rough edges to be found.Chainplates are conventional stainless steel flat bar, bolted to bulkheads and plywood gussets in the main cabin. These are properly backed with stainless steel pads. Due to the fact that the hull is lined throughout with a carpet-like synthetic material, it is not possible to examine the bonding of the chainplate knees to the hull. The stemhead fitting is a stainless steel weldment, through bolted to the deck and hull and reinforced inside the hull with a stainless steel gusset to prevent deflection of the deck from the pull aft of the headstay. We’d like to see a metal backup pad behind this fitting rather than the washers which are used.General construction is thoughtful and well executed, with excellent glasswork, a strong and simple hull-to-deck joint, and reasonably installed hardware and fittings.Handling Under PowerAlthough some early models of the 8.5 used a seven horsepower BMW diesel, the 1982 version employs an eight horsepower Yanmar. These small Yanmars are quite impressive, light in weight and far smoother than the company’s older rockcrushers.Because of the high freeboard and considerable windage of the 8.5, the standard engine is the absolute minimum power plant for the boat. Recognizing this fact, the company offered a 15 horsepower, two-cylinder Yanmar as an option. For another 75 pounds and $1,150, we would want this option on the boat if the ability to get places under power is a real consideration.The extra fuel consumption of the larger engine will scarcely be noticed. The 18 gallon aluminum fuel tank will probably give a range under power of over 250 miles—more than adequate for a 28 foot cruising boat.The fuel tank is located under the cockpit and is securely mounted and properly grounded. There is an easily reached fuel shut off between the engine and tank. Unfortunately, the fuel fill is located in the cockpit sole. Spilled diesel oil turns even the best fiberglass nonskid into an ice skating rink. Fuel fills should be located on deck, where spills can be efficiently washed away.Engine access is via a large removable panel on the inboard face of the quarterberth. This panel lacks any kind of handhold to make it easily removable, which will discourage regular checking of the engine oil. The top companionway step also removes for access, but it’s a long reach to the dipstick.There is no oil pan under the engine. It will be necessary to be very careful when changing oil to keep the bilge clean. We have yet to see anyone change oil and filters on a boat engine without spilling something.With the quarterberth panel removed, access for routine service is excellent. The quarterberth has remarkable headroom over, so that the mechanic will not feel like a trapped spelunker after a half hour of work. Engine removal will require some joinerwork disassembly.Handling Under SailThe S2 8.5 is no slug under sail. Her PHRF rating of 174 to 180 compares very favorably to other boats of her size and type. The Sabre 28, for example, has a rating of 198. The Pearson 28 about 195, and the O’Day 28 about 198.Part of this is no doubt due to the fact that the standard sails on the boat come from the North loft. While North’s OEM sails may not be the vertical cut Mylar-Kevlar wonders that adorn custom boats, they’re a lot better than most.S2 now uses Hall spars. The simple masthead rig is extremely clean, with airfoil spreaders and internal tangs. The boom features an internal outhaul and provision for two internally-led reefing lines, with cam cleats at the forward end of the boom.The deck-stepped mast is mounted in a stainless steel deck plate incorporating plenty of holes for the attachment of blocks. Halyards and Cunningham lead aft along the cabin house top to a pair of Lewmar #8 winches. Lewmar #16s are optional, but hardly necessary.The main is controlled by a six-part Harken rig mounted on the end of the boom, and a Kenyon traveler mounted on the aft cockpit coaming. This will work fine with the tiller-steered version of the boat. With wheel steering, the mainsheet is likely to be a nuisance to the helmsman.Because of the end-of-boom sheeting, a boom vang will be essential for full mainsail control. Ironically, the boat’s drawings show almost mid-boom sheeting, with the traveler mounted on the bridgedeck at the forward end of the cockpit. This is probably a better arrangement, although it heavily loads the center of the boom and requires more sheeting force.Owners of 8.5s have little but praise for the interior of the boat. The cabin has a wide feeling, created by pushing everything outboard. The “chart area” on the plan is a myth, as far as we can tell.Despite the fact that the shrouds are set well in from the rail, the boat lacks inboard headsail tracks. Rather, you are limited to snatch blocks shackled to the toerail track. A six-foot piece of track set inboard of the rail would be a useful addition.Standard headsail sheet winches are two-speed Lewmar #30s. Options include both larger winches and self-tailers, both of which are worth considering for either racing or cruising. The cockpit coamings are wide enough for mounting larger primaries and secondaries.The high-quality rig and sails add to the price of the S2, but they are additions well worth the cost.Deck LayoutThe deck layout of the 8.5 is clean and functional, with no toe stubbers to catch you unawares. There are two foredeck mooring cleats, but no bow chocks. The necessity to lead an anchor line well off the boat’s centerline, coupled with high freeboard forward, is likely to result in a boat which sails around on her anchor or mooring. The 8.5 has a pair of wide stainless steel chafing strips at the bow which will greatly protect the deck from the chafe of the anchor line.The 8.5’s foredeck anchor well is one of the best we’ve seen. It is shallow—just deep enough to hold an anchor and adequate rode. There are double scuppers, which offer less likelihood of clogging. The lid is held on by a full-length piano hinge, and there is a positive latch.The shallow locker well above the waterline means that water is less likely to enter through the scuppers, which can be a real problem with a deep anchor well. When the bow pitches into waves, a deep anchor well can fill with water, and if the scuppers clog with debris, you can find yourself sailing around with several hundred pounds of extra weight in the worst possible position. There is no provision for securing the bitter end of the anchor rode, but a big galvanized eyebolt installed in the well by the owner will solve that one.The running lights leave something to be desired. Their location at deck level just aft of the stem makes them vulnerable to damage when handling ground tackle. We much prefer an international style bicolor mounted on the pulpit, another two feet off the water: easier to see, and out of the way. Wiring for the running lights is exposed in the anchor well, and should be secured out of the way.A recessed teak handrail runs the full length of the cabin trunk, serving the dual function of heavy weather handhold and cabin trim piece. Its shape makes it far easier to oil or varnish than the conventional round handrail, although the wide, flat section seems somewhat awkward after years of grabbing round rails.The 8.5’s cockpit is the maximum size we’d want to see on a boat of this size. The T-shape is designed to accommodate the optional wheel steerer, yielding a somewhat odd layout for the tiller-steered version. A bench seat spans the aft end of the cockpit. Although this makes good seating in port, we doubt that you’d want anyone sitting there under sail: too much weight in the end of the boat. It does make a natural helmsman’s seat for wheel steering.The engine controls and instrument panel are also located at the aft end of the cockpit, and are basically inaccessible to the helmsman of a tiller-steered version.There are two lifting lids in the aft cockpit bench, giving access to a cavernous space under the cockpit. To be useful, dacron bags should be fitted to the inside of these lockers. Then, they’ll be handy stowage for spare sheets and blocks.There are comfortable contoured seats along each side of the cockpit, with a huge locker under the port seat. Although plywood pen boards somewhat separate this locker from the engine space under the cockpit, it would be far too easy for deeply piled junk to get knocked over the board and into the engine. This locker should be partitioned into smaller spaces unless it is to be used exclusively as a sail locker.The battery boxes, fitted at the forward end of the locker, could benefit from plywood or fiberglass lids to keep battery acid off gear which might find its way onto the batteries. The box is designed to take two batteries—one battery is standard—stored in plastic containers. A single lid covering the whole box would be more efficient.The huge cockpit will accommodate up to six for sailing, and eight for in-port partying. The cockpit seat bottoms are contoured, and the cockpit coamings slope outboard for more comfortable seating. However, the seats are both too narrow and too short for sleeping.The forward end of the cockpit is protected by a narrow bridgedeck. However, the cockpit coatings extend a full foot above the level of the bridgedeck, To block the companionway to the level of the top of the coamings will require leaving two of the three drop boards in place when sailing.Although there is moderate taper to the sides of the companionway, making it easier to remove the drop boards, it is still necessary to lift each board about five inches before it can be removed. This is far safer than many tapered companionways, where boards practically fall out if you look at them wrong. The companionway slide is one of the best we’ve seen. It’s a contoured piece of acrylic fitted with a convenient grabrail. It slides easily in extruded aluminum channels, and is fitted with a fiberglass storm hood. As on many boats, the aft cabin bulkhead slopes forward, rendering it impossible to leave the drop boards out for ventilation when it rains.BelowdecksOwners consistently praise the interior design and finishing of S2 sailboats. From looking at the 8.5, it’s pretty easy to see why.There are no exposed interior fiberglass surfaces except the head floor pan molding. The hull and cabin overhead are lined with a carpet-like synthetic fabric. While this will undoubtedly cut down on condensation, we at first wondered how this fabric would hold up over time. Inevitably, the hull liner and even the overhead will get wet. In freshwater areas, this is no problem. The water will eventually evaporate. In salt water, however, wet fabric never seems to dry. Salt draws moisture like a magnet draws steel. Since first seeing this boat, however, we’ve had good experiences with the fabric. Be sure, however, to get a good wet-or-dry vacuum to keep it clean.Interior layout is fairly conventional, with Vberths forward, and immediately aft, a full width head. The head can be closed off from both the forward cabin and the main cabin with solid doors—a real luxury in a boat this size. There is a large hanging locker in the head, and reasonable storage space for toilet articles.The word for the main cabin is “wide,” with the settees pushed as far outboard as they can go. Décor is a little heavy on the teak for our taste, but it is one of the better coordinated interiors we have seen. S2 had a good interior decorator.A fold-down dining table seats four. When folded against the bulkhead, it is held in place by a single latch, which makes us nervous.Neither settee is full length. The foot of the port settee runs under the galley counter, making it long enough for sleeping, although your feet may feel a little claustrophobic in the tiny footwell.The starboard settee is an unusual configuration. The aftermost 12" of the settee folds up to form an arm rest, leaving a gap between the end of the settee and the head of the quarterberth.Inexplicably, this gap is referred to on the accommodation plan as a “charting area,” although there is neither a standard nor an optional chart table. It’s sort of like the designer ran out of energy before completing the interior design.Over the non-existent “charting area” is the best electrical panel we’ve seen on a 28 foot boat. The panel has a locking battery switch, battery test meter, and a panel with room for 14 circuit breakers, although only half are installed on the standard boat.The space is welcome, since with the proliferation of marine electronics most electrical panels are woefully inadequate.Most quarterberths tend to induce claustrophobia. That of the 8.5 is more likely to exacerbate any tendencies you might have to agoraphobia. At last, a quarterberth which will not give you a concussion when you sit bolt upright in the middle of the night after your neighbor drags down on you in a wind shift.The standard main cabin sole is carpet-covered fiberglass. For an additional $325, teak and holly was available for the traditionalist. We’d want it. Unfortunately there is no access to the bilge in the main cabin. None. This is inexcusable, and could be dangerous. A few hours with a saber saw should solve this rather basic problem.The galley is workable and accessible, with no awkward posturing required to do the dishes. The sink gets an A+. It is a full nine inches deep, is large enough to take a frying pan, and mounted close to the centerline.In contrast, the icebox gets a C-. It is larger than normal on a boat of this size, but it drains to the bilge, has a poorly insulated top, and a tiny, uninsulated hatch without a trace of a gasket. Boo.Because of limited counter space, the two burner Kenyon alcohol stove is mounted athwartships, rather than fore and aft. This means that the stove cannot be gimballed, and that it is necessary to reach across the inboard burner to reach the outboard one. Given the fact that countertop gimballed stoves are usually dangerous, the lack of gimballing doesn’t bother us much. What does bother us is that if you want to upgrade the stove to something more functional, the limited space allocated will stretch your ingenuity.A fold down table at the end of the galley counter gives additional counter space, but it must be left up in order to use the port settee for sleeping.Roominess, excellent execution, and good color coordination are trademarks of the interiors of all S2s, and the 8.5 fits well into this enviable tradition.ConclusionsThe S2 8.5 is a good boat for cruising the Great Lakes or any coast in comfort and a certain amount of style. Her appearance may be a little modern for traditionalists, with her straight sheer and European-style cabin windows.Pricey? Yes, but when you look at the things that go into the boat—the rig, good sails, and a comfortable, well finished interior—the price may seem a bit less painful. You still pay for what you get.

1987 Hunter 28.5 sailboat, SE Michigan

Harrison, Michigan

For sale. 1987 Hunter 28.5 sailboat. It is in very good condition and very well equipped. Yanmar 2GM20 diesel that runs great. I took the boat from Lake St Clair to Cedar Point and back this summer. Asking $11,000 or best offer. Willing to consider trades for a 24-27 foot racer. Boat has the following:Self tailing winches, primaryNon self tailing winches cabin topRoller furling genoa with Harken roller furlingAssymetrical spinnakertelescoping whisker poleAutopilotLowrance Elite 5 GPS/Chartplotter/depth(fish finder) including all charts for the US and Canada.VHF radio with remote mic and speaker in the cockpitMostly new lines within the last 2 yearsAll interior cushions in good conditionDodgerhead and holding tankpressure water and hot water heateralcohol stovestorage cradle2 anchorsplenty of fenders and docklineslife jacketsthe well for the remainder of the year and winter storage are paid for, for the boat.

1982 Dufour 31 Sailboat

Oyster Bay, New York

1982 Dufour 31 Sailboat Original owner. Great sailing boat w comfortable living accommodations, powerful, easy to steer (wheel steering) and fast. Single handed sailing. 1.65 tons of ballast and 52 square meters of sail area equates to a formula that is both powerful and easy to manuever. Vessel is in the water, commissioned and ready to sail. Includes mooring in Oyster Bay, Long Island, New York for balance of the season. Includes an 8' Avon dinghy w Yahmaha 8 hp engine. Vessel is equipped w hot and cold water system, hand held shower, Adler-Barbour cold machine, 3 burner cooker w oven fitted on gimbals, ss sink w foot pump, locker under cooker and dish rack. There is a head w hand flush and holding tank. L-shaped set converts into a double berth. Navigation station. Full safety package. She sleeps five comfortably. Sails: Main, Genoa, Jib and Storm sail. Sail cover, dodger and bimini. Made to order canvas that covers entire cockpit. Ray Marine wind indicator, speedometer, w depth finders at nav station, and autohelm and auto pilot. Ray Marine Radar installed on mast and Ray Marine GPS, VHF radio, AM/FM w speakers in cbain and cockpit. Batteries #3 - solar power charger. LOA: 31. Beam: 10 Draft: 5.10 Engine: Volt 28 hp diesel, repowered 1989 Fuel: 13 gallons Bridge Clearance: 45' Displacement: 9,600 Ballast: 3,696 Designer: Michael Dufour Rig Type: Mastehead Sloop Headroom: Main Cabin 6.2, Head and Galley 6.0 Vessel is in very good condition as evidenced by the photos. Photos: www.sellyourboatnow.shutterfly.com Contact: Steve/Patty (631)896-6212

BEAUTIFUL TURNKEY SAILBOAT GREAT CONDITION

Long Beach, California

Make CAPITAL YACHTS

Model NEWPORT MK II

Category Daysailer Sailboats

Length 27.0

1983 Newport 27’ – Capital Yachts2 cylinder Universal diesel engine (engine was rebuilt in 2012)Auto bilge pumpHull cleaning & inspected once a monthDanforth anchor Holds 28 gallon of diesel (half gallon per hour)Holds 25 gallon of waterNew alternator in April 2013New battery 2014Changed oil & transmission fluid May 2015Furuno GPS systemSailed from Mission Bay in San Diego, to Catalina, then final destination Long Beach Marina Spring of 2013Sailed to and from Catalina again in March 2014 *** Boat has been in really good hands & very well taking care of*** Inside: Six foot of head roomTeak interior Two couchesSleeps five Mini refrigerator Dining TableGimbaled stove (propane)Pressurized working sink with regular faucet & an optional foot pumpWorking head (powered flush, macerator)New HD TVDVD playerAM/FM Radio with CD player, & Auxillary cable to connect with other devicesShip to shore radioFire extinguisher, flare Gun with flaresPlenty of storage room Outside: Dodger Roller furling Steering wheel with a tiller optionbbq grill Swim ladder Outboard motor mount 4 fishing rod holders 2 padded seat cushions 8 life jackets PREFER PAYMENTS TO BE MADE IN PERSONEMAIL [email protected]

1985 Tartan MKII 34, sailboat / Located In Stamford CT

Stamford, Connecticut

Make Tartan

Boat Name Rose Clair Cell #1 917-582-3435 Cell #2 917-363-0541 Rose Clair is a well maintained example of this classic Sparkman and Stevens designed Tartan 34 MKII This Tartan 34 has been primarily used for cruising around the Long Island Sound. In addition the Tartan 34 MKII model has won many distance races including the rugged Mackinac race and has also won high point in her class. The 34MKII is truly a high performance cruiser. If you are looking a great Racer Cruiser then be sure to take a look at this beautiful sloop. This Boat is Located in Stamford and is currently in the water / winter storage. She is covered and is available for viewing now. Storage is paid in full till 04/01/2017 Recent Upgrades Canvas and frame all new 2015 Sunbrella Canvas Mainsail Cover Dodger with side rails Bimini Dimensions LOA: 34 ft 4 in LWL: 28 ft 8 in Minimum Draft: 4 ft 5 in Displacement: 11000 lbs Engines Total Power: 24 HP Total Hours 800 Engine 1: Engine Brand: Universal Engine Model: 25M Engine Type: Inboard Engine/Fuel Type: Diesel Drive Type: Direct Drive Transmission: Hurth (new 2015) Tanks Fresh Water Tanks: 2 (57 Gallons) Fuel Tanks: 1 (23 Gallons) Holding Tanks: 1 (24 Gallons) Accommodations: The Tartan 34 MKII has accommodations for 6 people: Private forward cabin with "V" berth Enclosed head to starboard, with vanity, sink and Shower Hanging locker and drawers opposite Main salon amidships has settee to starboard which converts to double berth Single settee to port with plenty of storage Hinged bulkhead-mounted teak table w/bookcase behind Galley to starboard Nav station to port, with lift-top chart table Double quarter berth aft with storage Galley Single Stainless Steel Sink storage under Foot pump fro sea water and hot/cold water faucet Force 10 Burner Nat Gas. stove w/oven Hot Water heater (new 2015) and hot/cold pressure water system Top loading ice box Plenty of storage above & outboard in locker & drawers Sails and Rigging Full Batten main 130 Genoa on Harken furler Asymmetrical spinnaker with sock Spars and Rigging Coated Aluminum mast with two spreaders Coated Aluminum Boom Forespar Boom Vang Head Enclosed head (bifold doors) Single stainless sink with Hot/cold water faucet/shower. Holding Tank with Deck Pump-Out Mechanical and Systems Cockpit Wheel steering with Simrad autopilot and remote. Electric & manual bilge pumps Electronics and Navigation Gear Speed/Depth transducers VHF Radio with DSC and GPS Recent Upgrades Canvas and frame all new 2015 Sunbrella Canvas Mainsail Cover Dodger with side rails Bimini

Rhodes Bantam #1381 Sailboat, 14.5 ft. Mahogany. Restored 2008

Island, Kentucky

Length 14.5

Rhodes Bantam 14-foot of Honduran mahogany and African sapele plywood. A classic racing dinghy with lovely bronze hardware and wooden mast. Hull #1381, designed by Phillip Rhodes and built 2/1966 by Bill Kallusch Boats of Sodus Point N.Y.. This boat saw several years at Sodus bay (Lake Ontario) in New York. Later she was moved to Lake Champlain in Vermont for many years. She has sailed Kentucky Lake since 2006, infrequently of late due to owner being 28 years older than the boat... Restoration was completed in early 2008 included replacement of nearly all of the structural mahogany. Full treatment with CPES epoxy and 3M-5200 sealant allows the prospect of another 49 years of service. Three sails: main, jib and spinnaker all in excellent condition. Also included is a galvanized trailer. Boat is complete and ready to sail beautifully. Built for crew of two, with solo sailing accommodated. Hull is varnished inside and painted outside. The boat can be easily trailed as one person can lift and step the wooden mast. A great performing boat with beautiful traditional touches.

1974 Sabre 28-1

Chapin, South Carolina

Private Seller (301) 717-6471 Photos Photo 1 Photo 2 Photo 3 Photo 4 Photo 5 Photo 6 Photo 7 Photo 8 Photo 9 Photo 10 Photo 11 Photo 12 Close Request Information * Name First Name * Email Telephone (optional) Best Time to Contact Anytime Morning Mid-day Evening Question/Comments (optional) Shop Safely: Protect Your Money. By using this site, you agree to our Terms of Use. Contact Seller 1974 Sabre 28-1,Sabre 28 1974 Great shape very clean Great Family boat with lots of cockpit room as well as interior head room. Wheel steering Roller furling New interior cushions New working lines New helm and sail cover New traveler and boom vang New compass Auto helm Dodger (needs some re-stitching) Cockpit cushions Atomic 4 $10,900 Specs: http://sailboatdata.com/viewrecord.asp?class_id=975 Award winning (American Sailboat Hall of Fame 2003) Rodger Hewson design. The Sabre story began in 1970, when the company's founder, Roger Hewson, set out to build the finest possible 28-foot sailing yacht using production line methods and fiberglass technology. In a small, 4,000 square foot building, with a handful of employees and a vast amount of market research which he had done on the marine industry, he designed and built the first Sabre 28, and introduced it to the market at the 1971 Newport Boat Show in Newport, RI. The boat was a success, and over the next fifteen years, 588 Sabre 28's were built. $10,900, 3017176471 Be sure: Get a boat history report|Finance this boat|Get an insurance quote|

1983 Northwest 28

Olympia, Washington

NorthWest 28 Sailboat and Trailer Will consider trade for MacGregor 26X. I love the boat but it does not fit into our current life style. I am looking for a trailer able 25' to 27' swing keel sailboat such as MacGregor or Catalina. HULL Fin Keel 1983 Hand laid Fiberglass double hull with core- Built by Gary Lundy - Northwest Yacht Constructors LLC - Gorst Washington Built This sailboat was built as a hull kit only 5 were built. The original purchaser worked on it for years got sick and died. I purchased it from an estate auction and spent 2 years finishing it. It was surveyed in Aug. 2009 and the first launch was May 2010. LOA . 27 feet 75 in Beam . 9 feet in Draft . 4 feet 10 in Displacement . 8000 lbs Ballast . 3200 lbs. Skag and Rudder Wheel Helm RIGGING Masthead Sloop LWL . 23' - LOA 27' 8" Sail Area 400 sq. ft. Aluminum mast Deck-stepped Main sail CDI FF6 Roller Furler 135 Genoa All Lines run to cockpit for easy single handed sailing MOTOR Tohatsu 18 hp Runs great. Gas Setup for inboard motor if you desire. Has 1 1/4 in. shaft with drip less seal. The first year I ran a 23HP diesel engine. Wife did not like the hull vibration so I removed the diesel and installed an 18HP Tohatsu electric start with remote controls. Engine raises and lowers on a track. GALLEY / CABIN Sink with electric pump 2 burner alcohol cook top 12V refrigerator V- berth Single berth aft Port Enclosed head with porta potty GROUND TACKLE Danforth anchor on double aluminum rollers ELECTRICAL Autohelm 2000 . autopilot (wheel steering) 1 starter battery (1 1/2 years old) 1 house battery (1 1/2 years old) 600 foot Depth Sounder Amplifier that I plug in my I Touch into and outdoor speakers Wind Speed and Direction tied to Autohelm. 12V Winch mast raising / lowering system with tri-pod gin pole and accessories that allows raising and lowering the mast in as little as 30 minutes. TRAILER Comes with double axle with mounting for third axle if desired. It has 9 stands which allow raising and lowering of combinations of stands to allow access to all parts of the hull for painting. I stored the boat in my driveway in the off seasons allowing me access to my shop while working on the boat. Sails beautifully. Easily single handed. Must be seen and sailed to be appreciated.

1985 Tartan MKII 34, sailboat / Located In Stamford CT / Original Owner

Morgan WEST INDIES 36 SAILBOAT...Beautiful... in St Pete Fl.. EXTENSIVE refit

St. Petersburg, Florida

Make HERITAGE YACHT CORP

Model Morgan WEST INDIES 36

Length 36.5

Gorgeous, ...over 65k spent on refit....***1996 Perkins M30 fresh water cooled diesel***, low hrs. starts runs, excellent, no smoke, new oil and filter perkins m30 owners manuel Brand new bottom paint, 3 coats...12/2016, @ $2000 Built and designed by Charlie Morgan in Clearwater Fl. hull #4 of 40 built 36.5 feet on deck....38 feet overall length Heavy, thick hand laid FG hull and deck, combined with original robust construction... FAR EXCEEDS standard sailboats such as: islander, catalina, irwin,pearson, columbia, hunter, ericson etc... 11, newer solid Stainless Steel ports. 2 newer SS Lewmar deck Hatches. all new running rigging. newer ss Norseman cones all around custom SS mount mid boom mainsheet track with all new blocks '14 newer turnbuckles oversized lower shrouds internal halyards ***2014,... new (5) thick oversized massive SS electropolished chainplates. ... external lead keel dropped: new SS studs and bolts, and new SS backing plates, then rebed...new SS awthwartship stringers thrubolted under cabin sole...along with new SS mast step..rudder dropped, new rudder gland with new packing, new steering quadrant, new SS rudder boss, new steering cables....2014......all these above;...exceptional, laborious, expensive, extensive comprehensive metal refits. .****. seperates this vessel from just about any other vessel from this era....truly an incredible update refit..., on a deserving, thick , strong hull and deck..**** ..she's ready for another 50 years of service....*** an outstanding, capable sailing vessel...virtually one of a kind...! Pride of ownership evident Throughout!... mast rewired '14 new masthead tricolor light new mast mount foredeck light deck completely stripped of all hardware and Imron jet aircraft painted 2007, topsides and deck; with blue cove and boot stripes, shiny and beautiful...bulletproof...$600/ gallon,...yet another major, massive Expensive upgrade...update... new 2014 Garmin 740s color , touchscreen GPS navigation station vhf radio, stereo CD, dual speakers all new hoses and ss clamps on 1996 Perkins diesel engine and exhaust new engine water pump, 2014 merely 1100 hours,( low hrs.) on 1996 Perkins M30 diesel, ....runs, starts excellent, no smoke. new oil and filter on engine 12/16. new 1" thick engine room insulation /sound deadening new Raycor fuel filter plastic 28 gallon fuel tank, engine burns 1/2 gal /hour @ 6 knots cruise. 2 plastic water tanks, 80 gallons water total new cutlass bearing and shaft packing, '14,... 3 blade prop new 6 volt golf cart batteries,235 amps,... new deep cycle 12 volt engine start battery 135 amps.... 10/16 Pro mariner 20 amp 3 bank automatic battery charger new hi output 95 amp alternator and belt 6/16 new LPG princess 3 burner SS stove and oven new xtra custom cockpit scuppers with bronze valves, '14,... total 4 scuppers in cockpit new cockpit cushions '14 Teak cockpit floor grate, with blue canvas cover new canvas '14; to include... mains'l cover, hatch covers, new bimini top, new custom main compainionway hatch cover,... teak grate cockpit floor canvas cover. all new interior cushions '14 Excellent Lavac vacuum head, manuel, with 15 gal. plastic holding tank. 7 cu ft ice box with '90's engine driven grunert refrig freezer with holding cold plates, 1/2 hp compressor, needs work or replacement. newer stem head backing plate. CPT wheel autopilot, excellent 2009, over $2100 when new... new masthead windex '14. Simply, a magnificent well found sailing vessel, visually appears to be about 5 yrs old....Stunning,... everyone who sees her compliments her classic beauty. 55ft mast, 695 sail area yields excellent sailing performance, sails and rigging in very good condition.. 36' 5" on deck, 38 ft. overall, 4'2" draft, centerboard delete, trunk filled with 300lbs.lead and epoxy then sealed, Large rudder with large full skeg,.. 7300 lb.external lead keel,..17,000 lbs. dry unloaded...20,000 lbs. cruise loaded.... 12 ft beam,...* 32 foot long waterline.... sturdy , stable, stout, solid and strong... ..capable of sailing anywhere in the world.. USCG documented vessel,... no liens , privately owned outright. twin anchor rollers on extended spit, thus 38 ft overall, with dual hawse pipes and 2 anchor rodes with chain, 35 lb, cqr anchor. custom cockpit table/box stows 2 10lb LPG bottles and more newer inner forestay and running backs, cutter rig can be an option. or storm foresail hanked on. Airmar 200wx wx nav station, with masthead sensor, 2014 Airmar DT 800 bronze tranducer with 20 degree forward look 2014 16000 BTU marine Airconditioned,... cools excellent in summer Fl. heat 2014 ;NMEA 2000 wiring... for plug and play electronics and accessories SS Dodger frame included,no canvas though new marine 6 gal water heater,w new hoses new shower sump box with dedicated pump new cabin floor,..3 epoxy barrier coats applied , then 3 coats of bottom paint, no blisters. This vessel would have an Impeccable survey should you wish to have one...truly,... a one of a kind find...This boat has no rot, no rust,no blistering of any kind,... anywhere.. All bulkhead taping to hull is as the day she left the factory!... the interior frp liner/headliner is thick, solid strong and shiny!! 6' 4" headroom all interior cabinets and storages, cleaned and painted with quality superhard mildew mold resistant white exterior paint. CLEAN....! the bilge in this boat is...clean This boat has a cameo appearance in the 2011 Hollywood movie "Dolphin Tale" filmed in Clearwater FL. Kris Kristofferson lives on her in this acclaimed flick. The sailing photo is of this actual vessel taken after Imron paint. knowledgable, experienced, x captain, liveaboard cruiser, x boat builder, rigger; older private seller/sailor,.... needs no brokers or help in selling this fine boat,... whatsoever! over 800 labor hours of love and attention in the past 19 months, and it shows. She is exactly as pictured! Exceptional!... replacement cost? conservatively... $95,000 +, estimated professional survey value $64,000+...realistically priced at $36,500. numerous tools, spare parts, chart kits, hardware, screens , literature, magazines included in sale. she appears ....exactly.....as she is in the pictures....! looks better in person actually...a fine little ship... buyer responsible for vessel pick up in St Pete. Florida she could be kept at the same non liveaboard private house dock. she needs dodger canvas cover for supplied ss frame, fridge install, windlass (if your not younger) 1 more anchor bad back/disc forces reluctant sale..this is my dream boat; wanted to sail the Bahamas/Caribbean again...physically can't... more pictures available upon serious buyer phone request. also for sale at: sailboatlistings.com and Tampa Craigslist [email protected] seller, [email protected] not responsible for any shipping , buyer pays for any shipping costs. buyer must make full payment within 3 days. On Jan-19-17 at 07:26:36 PST, seller added the following information: The boat can be kept at its current dock/slip in south st pete fl. On Jan-19-17 at 12:26:10 PST, seller added the following information: Listed on SailboatListings.com

2001 J46 sailboat sail boat J-46 sailing cruiser racing fresh water. UPGRADES!

Charlevoix, Michigan

Make J Boats

Length 46.0

Beautiful, generously equipped and meticulously cared for freshwater J46 owned by senior couple. Used only for day sailing and minimal light cruising in northern Lake Michigan, Lake Huron and Lake Charlevoix for only 12 four month seasons (was not launched in 2012 and 2013). Always kept in inside heated storage when not in the water for the four month summer season. It is in pristine condition. J/46 may be the only investment grade sailing yacht of its size not requiring professional crew to sail at designed performance levels…..or to maintain. Two people can easily manage her upwind and down to achieve the same 8 knot passage-making speeds under sail that is possible when motoring with 76hp diesel auxiliary. The joy of sailing the perfect boat is, after all, a goal we believe every owner ultimately seeks. To insure that good sailing days are spent sailing rather than scrubbing and varnishing, J/46 is designed to be virtually maintenance-free. Her exquisite joinerwork is protected from the sun……below decks where it’s beauty can be preserved More photos available in this link: https://docs.google.com/document/d/1QEllizB6x4FKTe3kGwlbjYaLgJMrQEg8x6PdVtIa14Y/pub Factory Options: Refrigeration Package: -Seafrost Mechanical Refrigeration.-Additional Plates & controls for Freezer.-Supplementary 110VAC Shore power Assist. Supplementary Power Package: -Additional 210 amp Lifeline AGM Battery for total of 630 amps for house banks (location is in lieu of nav station bottom drawer).-Heart Freedom 25 Inverter/Charger (in lieu of std ProMariner 30-3 charger).-Heart Echo Charger (to service engine start battery through AC system).-Heart Link 2000 Battery Monitor (for (2) house battery banks).-Heart Link 10 Battery Monitor (for engine battery). Supplementary Plumbing Package: -Vacuflush Forward Head.-Dockside Water Inlet.-Seagull Water Purifier in Galley. Cruising Accessory Package: -Cockpit table.-Companionway Screens Additional Single Options: -ESPAR Diesel cabin heater.-Lewmar 64 CEST Power Primary Winches.-Bolstered Ultra Suede Cushions.-Radar Mast thru deck.-Microwave in galley.-Harken adjustable Genoa car leads.-Rubrail over cove stripe-28” High Pulpits & Stanchions in lieu of std height.-Sea water wash down pump w/faucet in anchor locker.-Hall Spars Windex.-Hall Spars “NO STRIKE’ lightning dissipater.-Hall Spars GAM antenna & cable.-Hall Spars painted carbon fiber whisker pole.-Hall Spar Whisker Pole Track and Car.-Hall Spars 3rd folding mast step.-Hall spars Dutchman mast sheave.-Hall spars Dutchman Halyard.-Flag Halyard & Hardware.- S. S. Turnbuckle Covers (6).-Cockpit Full Glass and Screen Enclosure.-Dodger to Bimini Insert.-Helm Pedestal Cover.-S. S. Grab Rail along aft edge of Dodger.-S. S. Grab Rails port & starboard on Dodger sides.-S. S. Dodger & Bimini supports in lieu of straps.-S. S. Bimini handrails port & starboard.-Power engine oil pump-out system.-Max Prop 3 Blade Feathering Propeller.-Dripless shaft seal.-Memory foam mattress in forward cabin in lieu of std.-Second custom V birth insert for additional standing room.-19” HD flat panel TV and small DVR.-2nd bottom refrigerator door.-Alpine stereo AM/FM w/6 disc CD player & Bose Marine cockpit speakers.-Weems & Plath Brass Ships Clock.-Weems & Plath Brass Barometer.-Variable Speed Cabin fans fore and aft cabins and main salon.-Prime bottom plus VC-TAR plus 2 coats VC-17 anti-fouling paint.-Awlgrip Hull Flag Blue w/Red Boot Stripes.-Patriot American Flag Graphics. Sail Package (Quantum): -Kevlar/Mylar/Dacron Tri Radial Cut full Batten Main & 135% Genoa.-MC6000 105% Cruising Jib.-Antal Mast Cars.-Dutchman Flaking System.-Asymetrical Spinnaker w/deployment bag.-Antal spinnaker Snuffer.-Harken Mark II Roller Furling System. B & G Hydra 2000 Navigator Pack: -Navigator Pack, Hydra 2000, Type 2.-Standard Full Function Display Pack, Hydra 2000.-20/20 Display Pack, Hydra, Green Backlight.-20/20 Display Pack, Hydra, Red Backlight.-Depth Sensor with Bronze Flush Mount Hull Housing.-Speed Sensor with Bronze flush Mount Hull Housing.-Analog display Pack, Apparent Wind Angle, 360 degrees w/cable.-Linear Rudder Position Sensor Pack, w/installation kit for Type 2 Ram.-Pilot Ram Drive Pack, Type 2 w/cables (12Vdc, adjustable rose joint).-Cable, 213 Mast w/bkt, 80ft.-Pin, Quick Release, Pilot.-Edson J46 Tiller Arm. Raytheon Radar/Chart Plotter and Accessories: -Upper Station – 7”Color LCD Pathfinder Radar w/Raychart and 24” 4kw Raydome.-WAAS GPS Antenna.-Cmap NT Northern Michigan.-Cmap NT Lake Huron and North Channel.-Radar Cable Connector (Radar Mast Base).-Edson 3-1/2” Deluxe Mast 144”.-Edson Adapter.-Edson Radar Platform, Deluxe.-Edson Long Antenna Bracket-Starboard and Port.-Edson 28” Antenna Hoop.-Edson 13” Antenna Extension (GPS antenna mount).-Shakespear TV Antenna 2030-G. Communications Options: -ICOM M502 VHF w/ Optional Cockpit HM-127 Remote-12 Volt Pedestal Outlet-Telephone and TV cable cockpit to nav station Safety Equipment: 2 Sospenders inflatable PFD w/harness, lanyard & rearm kit1 Crewfit inflatable PFD w/harness lanyard & rearm kit2 Regular PFD w/harness & lanyard4 Regular PFD6 Throwable floatation cushions2 Jack Lines 45 ft port & starboardI Radar reflector1 Bosun chair1 Throwable Life Sling1 deployable auto inflatable Life Saver Buoy4 Fire extinguishers – various types1 Submersible Hand Held HX460S VHF Marine Transceiver w/ barometer sensor1 Throwable Rescue Line Bag1 Avon 48lb Inflatable dinghy w/ Poly pro towing line, bridle & elect pump – fits in aft cockpit locker1 Honda 2hp 4 cycle dinghy motor & aft pulpit motor mount1 Winslow 6 person Super-Light Offshore Life Raft w/ SEP packed Survival Supplies Inflatable insulated double floor Heavy duty TriPod Arch tubes w/canopySpare parts: water pump impeller, 2 Racor fuel filtersVarious sizes of tapered wood emergency thru hull plugs 1 Handheld compass1 backup Yeoman digitized chart plotter with hand-held Magellan GPSVarious rescue flares as required by Coast GuardLakes Michigan, Huron and North Channel Charts Ground Tackle: 1 44lb Spade anchor w/swivel shackle, 25ft high test 3/8” chain and 250ft 5/8” rode1 Fortress Fx-37 Alum. Anchor w/ 15ft 5/16” chain & 200ft 5/8” rode in deployable anchor bag 250ft 5/8” Line for on-shore anchoring Dock Lines & Bumpers: 3 Taylormade bumpers w/blue covers6 Yale Red Colorline braided 5/8”x40ft dock lines w/Perma Buoy chafe guards Shore Power: 1 50ft 50 amp power cable1 60ft 30 amp power cable1 Adapter 50 amp to 30 amp Maintenance equipment: 1 Universal Pole w/boat hook, 2 brush heads & curve end1 50ft water hose Note: All 4 house batteries and the engine starting battery replaced May 2015 with Lifeline AGM (house) and Optimus (engine) batteries. J/46 Specifications Hull & Deck SCRIMpTM infusion molded sandwich construction using triaxial, biaxial and unidirectional glass reinforcements with Lloyd's and ABS approved end-grained balsa core. (SCRIMpTM is the patented resin infusion molding process of TPI Technologies, Inc.)TPI transferable ten yearwarranty against hull blisters. Interplastic vinylester resin on the outer hull layer.Lead & antimony fixed 9,350 lb., 6.2' draft, and fin/bulb keel bolted to a deep molded stub.White (other light colors are optional) Gel Coat hull with double tapered bootstripe and molded indented cove stripe. White gelcoat deck with choice of five non-skid colors in tones of white, gray and beige.HUIl-to-deck joint bond,ed with 3M 5200 and Plexus MASSO on the transom, side decks are covered with a thru-bolted clear anodized aluminum toe-rail.Two lazarette lockers on fantail, port cockpit seat locker and port utility locker for helmsperson outboard of wheel. Propane locker outboard of wheel to starboard drained and vented overboard with two 10lb aluminum bottles. Molded instrument pods on port and starboard coamings and on wheel pedestal.Molded companionway seahood with integral instrument pod.(3) Oorade boxes molded integrally into deck for ventilating owner cabin, main cabin and forward head area.Molded swim platform with off-center gate and fold-up ladder.Gasketed bow anchor locker and spinnaker storage area with overboard drain.316 stainless handrails on cabin trunk (4) total.GRP molded main structural bulkhead, glassed fore & aft on hull and deck as support for shroud chainplates with single door opening to v-berth cabin.Heavy duty molded structural keel support grid including engine bed, mast step, and longitudinal stiffeners. Fabricated aluminum mast step and engine bed tapping plates molded into structural keel grid.Positive traction nonskid on horizontal deck surfaces. Propulsion & Steering Yanmar 4JH-TE turbq-charged 76 hp, 4 cylinder, diesel engine with fresh water-cooling, dual R~cor fuel filters and 150 amp alternator.Yanmar C-type recessed engine instrument panel in cockpit with Acrylic cover including gauges for tachometer, fuel level, operating hour meter, fresh water temperature, amperage, oil pressure and oil temperature. Morse-type control gear shift and throttle mounted on pedestal.Parallel fuel system with 60 gallons in primary tank below the aft starboard berth, and 30 gallons in secondary tank behind aft bulkhead to starboard. Secondary tank gravity feeds into primary for 90 gallon total capacity.Two blade 20" Max Prop with 1..25" Aquamet shaft.AquaOrive self-aligning thrust bearing to minimize shaft vibration.Ultra Sound Acoustics VO-1 00 insulation in engine compartment.Balanced spade rudder constructed with unidirectional glass and large diameter shaft mounted in Harken composite rudder bearing to exceed ABS requirements.Aluminum emergency tiller.Edson 60" diamond series aluminum wheel with leather grip.Custom molded pedestal with guard and integral binnacle, 5" Ritchie compass, 9" x 12" instrurnent mounting area & Edson thru-shaft wheel brake.(2) Teak helm-station foot braces. Interior Satin varnished cherry bulkheads and furniture panels with cold molded cherry trim, drawer and cabinet faces. Main bulkhead with single opening and recessed cherry paneled door with Mobella lock-sets. Forward and aft heads trimmed in teak.Cherry trimmed vinyl headliner throughout forward, main and aft cabins. Polyurethane teak & holly veneer floor panels with underside and end-grain sealed with epoxy.Choice of interior cushion fabric colors. (ultra-suede or ultra-leather options available)5" layered & bolstered main settee split wrap-around cushions with two-tier split backrests. 4" foam cushions in fwd and aft cabins. Large twin berth forward cabin featuring 4 drawers, 4 lockers, hinge-up bunk tops to maximize storage; hinged V-berth filler; changing seat, hanging locker w/louvered door, and bureau/vanity with 2 drawers. locker. and cabinet above with cherry louvered doors & shelf.Forward head includes vanity with mirrored acrylic slider storage, teak towel rack, mirror storage cabinet below molded sink, enclosed by cherry paneled door (on outer face) and white laminate finish on head side.Stall shower with teak slat bench seat, cabinet locker with mid-height shelf outboard, shower fixture mounted on bulkhead with adjustable shower faucet. Local self-priming pump services shower sump and drains overboard.Pilot berth in main cabin to port with small mid-height convenience shelf at aft end.Two storage cabinets with 'Iouvered doors to ~ccommodate main cabin entertainment center above starboard settee. (2) Book storage shelves between cabinets with removable cherry retainer battens.One large drawer and one locker outboard of starboard settee backrest cushions.Settee backrests of cherry veneer and cherry trim.Varnished cherry wood hull slats in main, aft and V-berth cabins.Cherry main cabin drop-leaf table with removable fiddles, two drawers and internal bottle storage.Large 30 x36 sit-down. forward-facing navigation station with hinged tabletop. Features include; outboard shelf, access to chart storage and sliding organizer tray below table top, cushioned seat of layered bolstered foam. instrument cabinet with (2) large wood panel faces hinged at the bottom for quick access, file storage drawer below nav seat to fit hanging files, binocular & misc. storage cabinet outboard of seat, and series of three utility drawers on inboard tabie support face.Starboard aft cabin with recessed cherry paneled door, hanging locker with louvered door and bureau/vanity with 2 large drawers. hinged footlocker, and cabinet with cherry louvered door & shelf. Additional drawer above engine.Aft head/shower combination accessed via cherry paneled door. wet hanging area outboard. cabinet below molded sink, mirror, (2) teak grab rails and direct access door to lazarette locker area equipped with fore and aft divider. Teak companionway steps cold molded with angled ends & Treadmaster non-skid for safe entrance and exit. Cherry overhead grab rails in main cabin.All drawers and cabinets with polished positive-latch push buttons. Galley "Wheat Matrix" Fountainhead color for counter tops with cold-molded varnished & tapered cherry fiddles.Scandvik polished 8" deep SS double sink recessed below Fountainhead on forward island with deluxe hot/cold pressure-water gooseneck faucet and manual fresh water faucet with whale foot pump. Storage areas in louvered doors below sink for cleaning supplies and garbage pail with flip lid access.6.5 cu.!!. Deluxe icebox located on center island. Features include molded GRP box insulated with Glacier Bay Ultra R vacuum insulation panels and foam top. Organizing shelves & interior light included.3.5 cu.!!. ice box, convertible to optional freezer, located outboard of sink. Featuring molded GRP box with 3-1/2" foam insulation and mounting space for refrigeration cold plates.Three-burner Force 10 propane stove/broiler/oven with thermostat control, patented slide-away oven door recess and S.S. stove bar. Additional storage foot locker below oven.Plate, bowl, cup, and glass storage compartment on bulkhead att of stove.Top access dry good storage compartment below counter top directly outboard of sink.(3) Large cabinets mounted outboard and covered by three louvered cherry doors. Aft two cabinets installed with mid-height shelves. (Optional Microwave replaces middle cabinet door and area).Dual slider cabinet, bin storag8. and AC outlet mounted below cabinets. Flatware drawer, utensil drawer and utility cabinet with mid-height shelf and louvered door under outboard counter. Sink-top cutting-board.Stainless grab post on forward inboard galley corner. Plumbing Hot & cold pressure water system with 12-gallon hot water tank and accumulator tank. Service to (2) heads, forwa~d shower, galley, & swim platform shower.Self-priming direct sump pumps for showers draining into seacocks.Automatic bilge pump with float switch and dedicated panel in nav station wired direct to DC system. 120 gallons total water capacity in (2) custom molded tanks complete with baffles, inspection ports, and secured in place below main cabin settee berths.Raritan PH-2 heads with holding tanks. Overboard "Y"- valve offshore discharge and holding tank pump out systems. Two manually operated bilge pumps, one mounted in the cockpit and another in aft head with hose to reach bilge. (ORC category 2). Electrical Standard system batteries include: (1) group 40 (210 amp) and (2) group 31 (105amp) deep cycle batteries to serve the house, and (1) Optima 1000 (1,100 CCA) battery for dedicated service to the engine. All batteries are Concorde's Lifeline AGM sealed, absorbed glass mat type series.ProMariner ProMatic 30-3 Battery Charger. Balmar 91-150 Alternator and Max Charge external regulator with temperature sensor for altemator.BattJMaxx Automatic Battery System with remote momentary parallel switch near cockpit engine panel. .Master battery switch at n~l.Vstation with 1,2,Both,Off for House batteries and single On/Off switch for engine start battery.Deluxe Bass AC/DC backlit electrical panel w/digital condition meters, circuit breakers, accommodation for optional generator installation and air conditioning systems. Panel accommodates 33 DC breakers (24 occupied w/two spare standard) and 11 AC breakers (9 standard).Navigation, steaming/foredeck, anchor and tri-color masthead lights.50 amp 11OVAC shorepower system with 6 outlets, 50ft shore power cord and Guest galvanic isolator.Bonding system to meet ABYC project E-1.Propane solenoid switch panel in galley.Ten swiveling Imtra stainless halogen reading lamps, halogen overhead lights in main cabin, flexible armed lamp at navigation station, two florescent lights, one in each head.Four Hella variable speed cabin fans over berths. Deck Hardware (2) Lewmar 64CCST self-tailing 2-speed all chrome primary winches with gear ratio of 3.1: 1 in 1 gear and power ratio of 64:1 in 2nd gear located in recessed bases on cockpit coamings. "'(2) Lewmar 54CCST self-tailing 2-speed all-chrome halyard/reef/spinnaker secondary winches on cabin trunk.(2) Lewmar 48CCST self-tailing 2-speed all-chrome mainsheet winches outboard of traveler in recessed bases. (3) Lock-in Harken Speed-Grip 10" winch handles, (2) 8" Speed-Grip handles for mainsheet. Four cockpit mounted PVC winch handle holdersThurston cockpit dodger with roll-up forward window, removable side curtains, stanchion supports and stainless grab bar on aft edge.Thurston deluxe helmsman bimini with stanchion supports & viewing window (same color as dodger).Five white acrylic cockpit cushions for helmsman and cockpit seats.(2) Harken Black Magic 3010 (1OOmm) footblocks for genoa sheets when using dodger, mounted on cockpit coamings aft of primary winctTes. (2) Harken Black Magic 3006 (75mm) double footblocks with lock-off outboard of the primaries for spinnaker sheets and checkstays.(2) Harken Black Magic 3005 (75mm) mainsheet foot blocks wllockoffs mounted on angled pads at winches.2:1 Mainsheet system consisting of (2) Harken 1969 AirBlocks (75mm) mounted on traveler and (1) 3007 AirBlock (100mm) attached to boom bale. Harken 560-S Big Boat mainsheet traveler track with Harken 1939/1935 car w/control blocks for 6:1 purchase led to both sides of cockpit to 1893 track control ends through cockpit side mounted 222 blocks to 150 cam cleats. (2) 168 swivel blocks to adjust traveler from forward or aft side of track.Single rope clutchmounted in cockpit for heads ail furling. Lewmar Concept 2 anchor windlass system with #203 ropelchain gypsy, manual override, 1S0 amp breaker in nav station, hand held control unit mounted in forward deck anchor locker. Gypsy requires 3/8" ACCO G40 or G80 chain and S/8" braided rope.Custom 316 stainless mast collar with 10 bales for halyard and reef lines and forward halyard bar. (9) Schaefer 08-0S stainless halyard and reef blocks wlinvestment cast shackles.(4) Lewmar Superlock double rope clutches, mounted in pairs forward of each secondary winch.(2) Harken 1969 (7Smm) AirBlocks shackled to U-bolts at transom corners for mainsail checkstays.(2) Harken 1969 (75mm) AirBlocks shackled to U-bolts aft on toerail for spinnaker sheets.(2) Clear anodized aluminum "T" tracks (13' x 1.25") for jib/genoa leads. Additional 3' x 1.2S" track mounted outboard of1 00% jib position for outboard lead.(2) Schaefer 32-33UC screw-pin type jib/genoa lead blocks.(2) Schaefer OS-99 snatch blocks for spinnaker twingslor outboard jib/genoa leads.(2) Stainless t-track slider cars.Asymmetric.spinnaker deck gear including: (2) Harken 1969 (75mffi1 Airblocks mounted on "U" bolts near sternpulpit and (1) 1969 75mm AirBlock mounted on anchor roller.White molded flagstaff mounted in 316 SS deck socket on aft deck edge close to centerline with 4 x 6 American flag. aRC Bow pulpit of 316 SS with double rail offshore navigation lights and forward gate.aRC Stern rails of 316 SS w/2 rail split design including a stern boarding gate to starboard and stern light. Tapered 316 SS lifeline stanchions with SS bases mounted to toe rail.Double lifelines heights to meet ORC standards with boarding gates to P&S using Gibb hooks.Padded Sunbrella lifeline covers for each lifeline outboard of helmsman's station w/color to match dodger & bimini. Two 10" bow cleats, two 8" stern cleats, two 8" amidships cleats.Custom designed 316 SS bow roller/stem~ead to accommodate Simpson-Lawrence Delta 35,45 & COR 35,45 and Bruce 45 anchors. (Optional removable anchor roller to port)Seven Lewmar Ocean series articulated, bronze tinted ac,ylic hatches: size 70 on foredeck, size 60 in main cabin, (4) size 12 over forward cabin, aft cabin, shower, and head and (1) size 10 in aft head.White framed Bomar opening ports w/screen~ in cabin trunk and in cockpit walls for aft quarter cabin and head. Acrylic companionway hatch and two-part acrylic offshore drop-boards with inside/outside opening, lockable hasp. Four 12x20 and two 12x24 poly mesh line bags, one foredeck double line-bag. .(4) Vetus 4" dorade cowl ventilators to service forward cabin and head and main cabin. Removable stainless guards for forward dorades.316 SS swim ladder with gray PVC treads mounted on swim platform. SS step with PVC tread mounted on transom. Spars & Rigging Hall Spars carbon fiber mast of pre-preg carbon fiber autoclaved at 80 PSI at 250 deg F. Mast includes double airfoil carbon spreaders, carbon gooseneck, Awlgrip off-white finish, painted black bands, wire runs in conduit, Hall/Antal mainsailJrack with loader and end fittings to accommodate sail maker provided Antal mainsail sliders and/or boltrope. Also included with the mast are; Spartite mast wedge material, offshore tricolor/anchor light, bow and deck light with SS guard andJlag halyard cheek block at masthead and cleat at deck. Hall Spars boom of 6061-T6 aluminum with off-white Awlgrip finish, welded gooseneck fitting, lug for OuikVang internal 12:1 mainsail outhaul with external cleat, bale for mainsheet block and painted black bands. Outboard end to accommodate single line reef to starboard and 2nd clew reef to port. .Hall "J" length carbon fiber whisker pole with 2 bridles and trip line, short track on front of masJ, and two deck mounted retaining clips shipped loose for owner to locate.Navtec continuous rod rigging and N690 style open body turnbuckles with headstay -17 pre-assembled for furling system, backstay -17, uppers -17, intermediates -12, lowers -22.Harken MKIII Unit 2 size furling system with airfoil performance extrusion, corrosion proof spool and drum, tapered torque tube, AirSwivel for reduced weight aloft, cast aluminum Hardcote anodized chafe guard, and all black low stretch New England adjuster line.Hall Rigging package includes; two Technora jib halyards .and one Spectra spinnaker halyard each with Tylaska T-12 SS shackles and flemish eye terminations['2:'1 ',riain halyard of Technora with Wichard #1495 shackl~, XLS Mainsheet and two traveler control adjuster'lines, two XLS-900 Spectra genoa sheets, two Maxibraid taperedSpectra spinnaker sheets, one XLS Dacron spinnaker tack line, single 3/8" Crystalyne checkstays that can beclipped forward when not in use, burgee halyard of white 5/32" Dacron cord. Three reef lines are also included; Tack reef & clew reef #1, together, are one continuous reef line to starboard. Tack reef #2 doubles as cunningham to port. Clew reef #2 is included with it's own dedicated hardware. 2:1 Whisker pole foreguy with Schaefer 504-09 block with snap shackle.Sailtech -17 Long integral hydraulic backstay adjuster. Hall D-30 aluminum Ouik-Vang w/ Harken 30:1 cascading adjuster tackle & powerful stainless return spring to lift boom in light air and support boom with sail furled, eliminating the need for a topping lift.Custom designed 316 SS chainplates, stemhead and backstay tang. Installed Package Options Refrigeration PackageSeafrost Mechanical Refrigeration.Additional Plates & Controls for Freezer Supplementary 11OVAC Shorepower Assist. Supplementary Power PackageAdditional 210 amp Lifeline AGM Battery for total of 630 amps for house banks (location is in lieu of bottom nav station drawer).Heart Freedom 25 Inverter/Charger (in lieu of standard ProMariner 30-3 charger).Heart Echo Charger (to service engine start battery through AC system).Heart Link 2000 Battery Monitor (for (2) house battery banks).Heart Link 10 Battery Monitor (for engine battery). Supplementary Plumbing Package Vacuflush Forward Head. Dockside Water Inlet.Seagull Water Purifier in Galley. Cruising Accessory Package Cockpit Table.Companionway Screens.Espar D5LC heating system with ducting into the two sleeping cabins and main cabin.Lewmar 64CEST Two Speed Electric Primary Winches.UltraSuede or UltraLeather Covered Cushions in Main Cabin (in lieu of standard).Edson Radar Mast Thru-Deck and under-deck mounting platform (for 3.5" diameter mast). Microwave Oven in GalleySea Water Washdown in Anchor Locker.Harken Adjustable Genoa Leads.Many additional photos herehttps://docs.google.com/document/d/1QEllizB6x4FKTe3kGwlbjYaLgJMrQEg8x6PdVtIa14Y/pub Manufacturer Provided Description Great boats don’t happen overnight. Helped by new materials and techniques, they evolve from the joint experiences of designer, builder and owners to become state-of-the-art. J/46 is such a vessel, inheriting the proven hull shape of the J/44, an offshore blue water classic, having won the Fastnet, Sydney-Hobart, NYYC Queen’s Cup and Trans-Atlantic races. J/44 is the only Class of yacht ever to be given its own class start by the Cruising Club of America in the Newport-Bermuda Race. To create the J/46, a foot of sailing length is added for speed; a transom swim/boarding platform for convenience; a carbon fiber mast and low VCG 6.2’ shoal draft keel for more stability; and a resin-infused, composite hull and deck for greater strength. Below decks, the choice was clear, use the same beautifully varnished cherry or teak joiner work, entertainment center and styling so highly acclaimed in our deluxe J/160. J/46 is a maxi-Ditch yacht, the tallest yacht that can fit under the bridges of the Intra-Coastal WWaterway. Yet she is non-intimidating. A high length-to-beam ratio on the waterline of this sea-kindly yacht significantly improves tracking offshore in large waves and makes sail plan balance less critical. J/46 sails with either main or jib only, always responding predictably to a light touch on the helm. Sail power with good stability allows cruising with working jib rather than large genoa. That’s less work for the crew and improved visibility for the person on the helm. J Boats’ unique spinnaker system makes downwind sailing possible for two. A modern asymmetric spinnaker attaches to the top of the anchor roller, is contained within a cockpit-controlled snuffer, and is stored, ready-to-use, in the bow locker. The spinnaker is hoisted to the masthead, 2’ above the headstay intersect, leaving space for the snuffer to shift on a jibe. Jibing is then easy. One simply lets off one spinnaker sheet and pulls in the other.

1985 NONSUCH 30 SAIL BOAT - ULTRA CONFIGURATION

East Norwich, New York

Make NONSUCH

Model ULTRA Layout

Category Sailboats

Length 30.4

Welcome to the world of NONSUCH sailing: If you are familiar with the uniqueness of the NONSUCH, please procede below, if not, please Google Cruising World .com for a full review and history of NONSUCH and why it is such an incredible boat. I tried to post the full link below but EBAY forced me to remove it. If you add a www in front of the link below and cut and paste it into google search, the article should come right up. cruisingworld.com/sailboats/boat-reviews/nonsuch-30-an-utterly-uncomplicated-cruiser Caution: The reason we have not placed this boat in the water is because we want any prospective buyer to be re-assured that the boat is just as perfect below the waterline as it is topside. You can run a moisture meter anywhere you want on "Sophisti-Kat" and you will find a boat as dry as it was the day it came from the factory. Beware of any boat being sold that is already in the water and make sure to have the owner place it on “The Hard” before making your purchase so you can make sure you are getting a sound boat. Many older boats are placed in the water when being sold to hide blisters and saturated fiberglass. Now let’s get started...........please review my feedback so you can be assured that you are buying from a provider with the utmost integrity. I pride myself on only selling excellent product that buyers will be proud of for years to come. This boat is my Father's boat, he is the original owner and the boat has always been in our family. Welcome to my auction for "Sophisti-Kat" a 1985 NONSUCH 30 ULTRA. This is a very highend limited production sailboat built by Hinterholler Yachts, Ontario, Canada and designed by Mark Ellis. While there may be other NONSUCH 30's for sale on the market, this boat is extremely unique for two specific reasons: 1) Most of these boats were heavily cruised or raced; "SOPHISTI-KAT" was never cruised and was never raced. She spent most of her life on her mooring and was used for light family sailing and barbeques. The pictures clearly demonstrate this. 2) The other reason that this boat is unique is because it was purchased and built to my father's specifications meaning it is the "ULTRA" layout, not the standard layout and was equipped for global travel even though it rarely left the mooring. This boat has the upgraded bullet proof Westerbeke engine, Here is a breakdown of the boat: Overall Dimensions LOA: 30.4 Feet Beam: 11.10 Draft: 5 Feet LWL: 28.9 Displacement: 11,500 Ballast: 4500 Bridge clearance: 53 feet Headroom: 6.3 feet. "Sophisti-Kat" is Documented and Insured for $ 90,000 Auxiliary Power Westerbeke, 27 horsepower Diesel inboard engine Fuel capacity 30 gallons Fuel consumption, about 2/3 of a gallon at 2200 per hour New fuel and water Separator, required by Coast Guard Three 12 Volt Batteries Major Options Seafrost Refrigeration System - Used on the most expensive yachts Espar Central Heating System (Made in Germany) the Best Diesel heating system available Gimbaled Hiller Range Stove - Top of the Line Paloma Propane water heating system for all sinks and shower Special Nova Sentry Panel provides AC Shore Power for (Refrigeration, Battery Charger, and All GFI Outlets) Professional Marine 35 AMP Battery Charger Special "Hideaway" Bimini Propane "SENSOR" Alarm System - provides maximum protection Master Electronic Winch - For raising the Mainsail Auto Pilot - Navico 4000 Dripless Coupling on Drive Shaft replacing old style Stuffing Box - New Custom Teak Boards cover the Cockpit Sole Upgraded Fluorescent Lighting Standard Horizon VHF Data Marine. LX-360 Wind Machine Datamarine Depth Sounder Emergency Radio Antenna Electric Bilge Pump Six new Imtra Brass Reading Lamps (Italian & Very Expensive) Custom made Cockpit Cushions Full teak rub rail and double life lines with Port and Starboard Gates Several years back, the bottom received a Barrier Coat to protect against Osmosis, this is extremely expensive and time consuming but lasts the lifetime of the boat. All through hull fittings have been replaced and upgraded to Bronze for safety purposes Life Sling "Man Overboard Rescue System" 50 Foot Shore Power Cord Freshwater water Capacity is 86 gallons Holding tank 24 gallons (Never Used) Accommodations Two cabins separated by a Teak folding Door. Forward Cabin. . Double Berth to Port, with upper shelf for storage. Beneath the Berth is a large fresh Water Tank, with storage space that includes two small vertical Drawers A hanging closet is forward, between the Berth and Dresser area on the Starboard side. This has a Counter top, Mirror and storage area behind sliding Lucite doors. Under the counter is storage space plus three vertical Drawers. It has access to the shower and Head towards the starboard side prior to the folding Doors. The Main Cabin has access to this area on the other side of the Doors. The Shower Salon and Head Areas are separated by a Shower Curtain. There is a teak seat and storage area within the Shower Salon. The Head area contains a Counter that includes a Stainless Steel Sink. Under the sink is storage space and access to the Bronze thru hull fittings. Located above the Head and Counter is a Shelf with sliding Lucite Doors for Bath Room Items Main Cabin The Galley is L shaped, and located on the Port side with a large Counter top. A deep Stainless Steel Sink is supported with both Manual and Automatic systems to provide Water Access. Located below the Sink is a stowage locker to store, Cleaners and various other articles. Also provides access to Bronze thru Hole fittings, and pump for different water flow settings. Adjacent to Port are four vertical drawers to accommodate further Storage. Above this area, is where the Paloma Propane water heating system is located. It provides Hot water, thru out the vessel. This area also includes a Shelf with sliding Lucite Doors to store Wine Glasses and other Galley Items. Port to the sink is the cold storage area provided by the Seafrost Refrigeration System that eliminates the need to store ice. Above this area to Port is a large shelf behind Lucite sliding Doors. It provides enough room for Dishes, Cups, Glasses, Canned products and other various supplies for meals. Aft of the cold storage area is a Gimbaled Hiller Range Stove and Oven. Aft is a 6’6 Foot Settee and behind the support cushions are two storage areas. Under the Settee is the other water tank plus additional storage. Aft of the Settee is a Hanging Closet. Opposite on the Starboard side is a 6, 7 ft. L shaped settee and dinette set up. When the dining table is lowered the area converts to a double berth in the standing position the table is also used for Navigational purposes. The Espar heating System Thermostat is located upper left of Dining Area Bulkhead. Sail & Canvas Sail area is an incredible 540 Sq. feet, with two reefing points. Raising the Sail is simplified via the use of the Master Electronic Winch. In addition to Raising sail, all aspects of necessary sail adjustments, including, reefing are controlled within the Cockpit. When the Sail is lowered, it settles into Lazy Jack Lines. The Sail Cover is in good condition and the Mainsail was always covered and never exposed to the Sun or other elements. The Dodger is in excellent condition. It's custom made with openings to provide good airflow. In foul weather, it has Eisenglass inserts for full enclosure which have never been used. The matching Bimini is of special design. When not in use, it uses track and slides to disappear behind the aft Combing. Special designed Teak Boards cover the Cockpit Sole .The section behind the Helm is raised and curved to comfortably stand depending on point of Sail. The Helm has a compass and Teak Table. There are three lockers in the Cockpit, Port and Starboard, with easy access to the Engine, the third aft for two Propane tanks. Extra lines etc. The folding swim Ladder is located on the Stern. Entrance to Below Deck is via Lucite Companionway Doors. Inside, on the Upper Starboard side is the outlet for the Master Electronic Winch. Nearby, is a DC outlet to accommodate, charging cell phones or other appliances. Custom made Cockpit Cushions cover the entire seating area, when not in use; there are 6 floatable cushions available. Forward, the Vessel has a bowsprit with rollers to accommodate two anchors, A 35 lb. CQR and 30 lb. Danforth.... Additional Equipment .includes, Fairclough Winter Cover, Fire extinguishers, fenders, life jackets, Dock lines and extra lines. "Sophisti-Kat" is an incredible find and listed for thousands below here true value. I think you will be hard pressed to find another NONSUCH 30 ULTRA even remotely close to her condition and with her equipment. Please feel free to write with any questions as I will be happy to answer them "Sophisti-Kat" is also listed locally and I reserve the right to end this auction at any time. This boat is ready to go into the water and is 100% prepped for sailing and powering. No warranties are expressed or implied but I do guarantee the boat is everything that I have stated here and my feedback speaks for itself. Best of luck with your bidding.....................

1986 25 fT. McGregor Sail Boat with Trailer

Pottstown, Pennsylvania

FOR SALE 1986 25 FOOT McGREGOR SAIL BOAT WITH MOTOR AND TRAILOR THIS IS A ONE OWNER BOAT. WAS PURCHASED NEW BY SELLER IN 1986 AND USED ONLY BY SELLER. THIS BOAT IS 28 YEARS OLD, SOMEWHAT WELL KEPT, SEAWORTHY, NEVER IN AN ACCIDENT, AND NEVER HAD A HOLE. USED IN SALT AND FRESH WATER. WAS REPAINTED BY OWNER WITH MATCHING FACTORY COLORS SEVERAL YEARS AGO. 9.9 MOTOR INCLUDED. TRAILER IS INCLUDED AND WAS PURCHASED NEW WITH BOAT. ALSO INCLUDED IS A MAIN SAIL, JIB, AND A RAINBOW GENOA SPECIAL MADE FOR THIS BOAT. INTERIOR HAS BERTS FOR FIVE PEOPLE, DOORED TOILET AREA, AND A FOUR PERSON DINETTE THAT CONVERTS TO A DOUBLE BERTH. THERE IS ALSO A BUILT IN ICE CHEST. A GREAT STARTER FOR THE NOVICE OR A NICE STEP UP FOR SOMEONE LOOKING TO SEE IF A BIGGER SAILBOAT IS RIGHT FOR THEM READY FOR FUN, JUST ADD YOU AND SOME WATER THANK YOU FOR LOOKING!!!!! PLEASE EMAIL ANY QUESTIONS. It may be a day or 2 to respond as I am listing this for my Grandfather.

Narrow Results

Current search reset all.

• Keyword: 28 foot sailboat
• CAPITAL YACHTS (2)
• HERITAGE YACHT CORP (1)
• J Boats (1)
• NONSUCH (1)
• Cruiser Motorcycles (2)
• Daysailer Sailboats (2)
• Sailboats (1)
• California (3)
• Michigan (3)
• New York (3)
• Connecticut (2)
• Florida (2)
• Kentucky (1)
• Pennsylvania (1)
• South Carolina (1)
• Washington (1)
• Wisconsin (1)
• POP Yachts (1)
• Search Title Only
• Has Picture
• Include Sold Listings

Showcase Ads

2017 Sun Tracker 20DLX

Lake Havasu City, AZ

2008 Sea Ray 260 Sundancer

2014 Malibu Wakesetter 22 MXZ

Addison, TX

2004 Crownline 270 CR

Green Bay, WI

2011 MB Sports F21 Tomcat

Canyon Lake, CA

2016 Tidewater 2200 Carolina Bay

Montgomery, AL

2015 Robalo 226 Cayman

Cleveland Heights, OH

Create Alert

Please, name this search

Select Interval

Alert Successfully Created

Home > Find Your Sail > Search by Make and Model > Hunter > Hunter 28.5

Hunter 28.5

" * " indicates required fields

Step 1 of 3

Let's Get to Know Each Other

Let's connect, your trusted partner for hunter 28.5’s:.

Building Lasting Relationships Through Quality and Precision

Our team of Precision Sails experts conducted extensive research on the web to gather information about the specific sailboat in question. We thoroughly scoured various online sources to compile relevant and accurate information for the boat owner. Our team carefully curated the information to ensure that it would be helpful and informative for the user. We understand the importance of having a deep understanding of your boat’s features, and our goal is to provide comprehensive and reliable information that will enable boat owners to make informed decisions about their sailing experience. By sharing our expertise and knowledge, we hope to empower our customers to get the most out of their sailing adventures.

All About Your Hunter 28.5

Rig specifications.

These are the specifications provided by the designers, but even from the factory, these boats may not be identical. The reason for this is that the sail industry often contracts manufacturing to different sources in order to achieve economies of scale. What this means is – your Hunter 28.5 may be more unique than you initially thought.

It’s important to note that boats are also frequently customized, so if you suspect that work has been done on yours, it’s best to take your own measurements. When ordering a sail, we will advise you if using the manufacturer’s specifications is appropriate, or if we require you to complete our own measurement forms.

I: 37.33 ft / 11.38 m

J: 12.08 ft / 3.68 m

P: 31.75 ft / 9.68 m

E: 10.83 ft / 3.30 m

Despite its compact size, the Hunter 285 is a highly capable sailboat that is designed to perform well in a wide range of conditions. As designed by the Hunter Design Team, the Hunter 28.5 sailboat sports a complex B&R rig with a split backstay. It has a mainsail area of 225.47 sq. ft. and a jib sail area of 171.93 sq. ft. This powerful sail plan is optimized for speed and maneuverability, as well as a deep keel that provides excellent stability and control.

The Hunter 285 features a sloop rig with a single mast, allowing for a familiar sail plan of a mainsail and a headsail, with the option of a spinnaker or genoa for an additional performance boost in light wind.

Performance

The boat’s sail plan is optimized for speed and maneuverability, with a high aspect ratio that provides excellent performance in a wide range of wind conditions. The boat is also equipped with a boom vang and adjustable backstay, allowing for precise control of sail shape and tension.

The Hunter 285 is also equipped with a reliable diesel engine that can provide ample power when needed. With its combination of speed, stability, and maneuverability, the Hunter 285 is the perfect sailboat for those seeking adventure on the high seas.

Design Features

The Hunter 285 is a compact, yet highly capable sailboat that is perfect for sailors of all experience levels. This design was first built in 1985 by the Hunter Marine Co. and was later revamped into Hunter 28 by the renowned naval architect, Rob Mazza, the Hunter 285 features a spacious cockpit and a comfortable, well-appointed cabin that can accommodate up to six people. One of the standout features of the Hunter 285 is its innovative design. The boat features a sleek, modern hull design that is optimized for speed and maneuverability. The boat also features a deep keel that provides excellent stability in rough seas.

The Hunter 285 has a displacement of 7,000 lbs and a lead ballast of 3000 lbs. And the LOA is 28.5ft with a beam of 10.5ft. The Hunter 285 also features a spacious cockpit that is perfect for entertaining guests or relaxing with friends and family. The cockpit is well-equipped with all the necessary sailing instruments and features a large steering wheel for easy maneuvering.

Cabin Layout and Amenities

The Hunter 285 features a well-appointed cabin that is both comfortable and functional. The cabin features a large V-berth that can comfortably sleep two adults, as well as a settee that can be converted into a double berth.

The boat also features a fully equipped galley with a sink, stove, and refrigerator, as well as a private head with a shower. The cabin is well-ventilated and features plenty of natural light, making it the perfect place to relax and unwind after a long day on the water.

If you’re looking for a high-quality sailboat that is both stylish and functional, look no further than the Hunter 285. With its innovative design, comfortable cabin, and exceptional performance capabilities, the Hunter 285 is the perfect vessel for sailors of all experience levels.

Recommended Sails For Your Hunter 28.5

We would love to help you enhance your sailing experience on your Hunter 28.5. That’s why we have put together a list of expertly curated sail recommendations just for you. You can find more information about each sail and their specific uses by following the links to our education page.

You need a mainsail designed to give you the greatest mileage out of your vessel. Precision Sails’ custom designed mainsails come with all the standard options needed to get sailing right away, and custom options to optimize handling, performance, and shape.

Jibs, genoas, yankee cut, staysails, or working jibs, we do it all. No matter what headsail you need for you sailboat, Precision Sails’ team of sail designers will work with you to ensure your new head sail fits and performs for you. Our headsails come complete with all standard options required for the best performance and durability. Learn more about our available headsail options and customization here.

Downwind and Light Wind Sails

Sail downwind easily with your choice of our downwind and light wind sail options. We custom design and tailor every sail for your needs. Explore our symmetrical or asymmetrical spinnakers and code zeros, including what options are available for each.

Request a Hunter 28.5 Quote

Looking to buy a new headsail or mainsail for your Hunter 28.5? Request a free quote from Precision Sails for a new custom sail. Our team will work with you to design the perfect sail for you.